Camshaft Drive Gear - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 6V-6080     | 扭矩倍增器     | 1     |
5P-1748 | 套筒     | 1     | |
B     | 213-3110     | 套筒 (1)     | 1     |
4C-9818 | 六角适配器 (1)     | 1     | |
4C-9819 | 万向节 (1)     | 1     | |
4C-9927 | 钻机 (1)     | 1     |
Show/hide table
( 1 ) | 此工具可用于转动曲轴。 |
开始:
- 卸下磁电机。 请参阅拆解和装配, "磁电机 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从发动机的侧面拆下后凸轮轴检查盖。 从保存位置拆下凸轮轴正时销钉。 使用手摇盘车总成转动发动机,直至可将定时销安装在曲轴和凸轮轴内。
- 接合并锁定手摇盘车总成,以防拧松螺栓 (4) 时发动机转动。
Show/hide table
图 1 | g00560389 |
- 从曲轴和凸轮轴上卸下定时销。
- 使用工具 (A) 拧松螺栓 (4) 。
- 卸下螺栓 (4) 和垫圈 (3) 。
- 卸下螺栓 (2) 和盘 (5) 。
- 将垫圈 (3) 放在凸轮轴和盘 (5) 之间。 安装螺栓 (4) 。
- 安装螺栓 (2) 并用手拧紧。
- 均匀地拧紧螺栓 (2) 以便从凸轮轴锥状顶端上拉下凸轮轴主动齿轮 (1) 。
注: 当拉动齿轮,将其与凸轮轴锥状顶端脱离时,要确保螺栓 (4) 已安装以便固定凸轮轴主动齿轮 (1) 。
- 将适当的起吊设备连接至凸轮轴主动齿轮 (1) 上。 卸下螺栓 (2) 、螺栓 (4) 、盘 (5) 和垫圈 (3) 。 从后壳体上卸下凸轮轴主动齿轮。 凸轮轴主动齿轮的重量约为 35 kg (77 lb)。
Caterpillar Information System:
G3408 and G3412 Engines Engine Oil Pressure Indicator
G3304 and G3306 Engines Water Temperature Indicator
G3408 and G3412 Engines Ammeter
G3304 and G3306 Engines Overspeed Contactor
G3408 and G3412 Engines Voltage Control Relay
G3408 and G3412 Engines Service Meter
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Solenoid Valves
G3408 and G3412 Engines Circuit Breakers
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Electric Motor (Gearbox Oil Pump)
G3408 and G3412 Engines Pressure Switch
G3408 and G3412 Engines Magnetic Switch
G3606 and G3608 Engines Magneto - Remove and Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Transmitters
G3606 and G3608 Engines Camshaft Drive Gear - Install
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Switches
Electric Protection System Energize-To-Shutoff (ETS) For Generator Set, Industrial and Marine Diesel Engines Troubleshooting the ETS Full Protection System (OP, WT, OS)
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Disassemble
G3606 and G3608 Engines Idler Gears (Rear) - Remove
G3606 and G3608 Engines Idler Gears (Rear) - Install
G3408 and G3412 Engines Ignition System
G3408 and G3412 Engines Air Inlet and Exhaust System
G3606 and G3608 Engines Idler Gears (Front) - Remove
G3606 and G3608 Engines Idler Gears (Front) - Install