Idler Gears (Rear) - Remove
拆卸步骤
开始:
- 卸下凸轮轴主动齿轮。 请参阅拆解和组装, "凸轮轴传动齿轮 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将适当的起吊设备连接至惰轮组件 (2) 上。 惰轮组件 (2) 的重量约为 54 kg (119 lb)。 卸下护圈 (1) 。 从轴上卸下惰轮组件 (2) 。
Show/hide table
图 1 | g00561144 |
注: 不需要卸下后壳体。 卸下后壳体仅供拍摄。
- 拆解惰轮组件:
- 卸下螺栓 (5) 。 将齿轮 (6) 从齿轮 (3) 上分离。
- 如有必要,从齿轮 (6) 上卸下轴承 (4) 。
Show/hide table
图 2 | g00561145 |
- 卸下止推垫圈 (8) 。
Show/hide table
图 3 | g00561146 |
- 将适当的起吊设备连接至轴 (7) 上。 轴 (7) 的重量约为 25 kg (55 lb)。 拆下螺栓 (9) 。 从缸体上卸下轴 (7) 。
- 如有必要,从轴 (7) 上卸下销。
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Disassemble
Electric Protection System Energize-To-Shutoff (ETS) For Generator Set, Industrial and Marine Diesel Engines Troubleshooting the ETS Full Protection System (OP, WT, OS)
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Switches
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Install
G3606 and G3608 Engines Camshaft Drive Gear - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Transmitters
G3606 and G3608 Engines Camshaft Drive Gear - Remove
G3408 and G3412 Engines Engine Oil Pressure Indicator
G3304 and G3306 Engines Water Temperature Indicator
G3408 and G3412 Engines Ammeter
G3304 and G3306 Engines Overspeed Contactor
G3408 and G3412 Engines Voltage Control Relay
G3606 and G3608 Engines Idler Gears (Rear) - Install
G3408 and G3412 Engines Ignition System
G3408 and G3412 Engines Air Inlet and Exhaust System
G3606 and G3608 Engines Idler Gears (Front) - Remove
G3606 and G3608 Engines Idler Gears (Front) - Install
G3606 and G3608 Engines Magnetic Pickup - Remove and Install
G3606 and G3608 Engines Housing (Front) - Remove
Digital Voltage Regulator KVAR Regulation
Digital Voltage Regulator Power Factor Regulation
Digital Voltage Regulator Voltage Regulation
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Assemble
Digital Voltage Regulator Line Loss Compensation