Camshaft Drive Gear - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 6V-6080     | 扭矩倍增器     | 1     |
5P-1748 | 套筒     | 1     | |
B     | 4C-5592     | 防粘结剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在凸轮轴中安装凸轮轴定时销 (6) 。
Show/hide table
图 1 | g00560389 |
Show/hide table
图 2 | g00560651 |
注: 如果凸轮轴内不能安装定时销,可能需要拧松摇臂和进气阀的调整螺钉。 这样做可以转动凸轮轴。
- 将正时销钉安装到曲轴内。
- 将盘 (5) 放在凸轮轴主动齿轮 (1) 上的合适位置。 安装螺栓 (2) 。
- 将工具 (B) 涂敷在螺栓 (4) 的螺纹上。
- 使用适当的提升装置。 凸轮轴主动齿轮的重量约为 35 kg (77 lb)。 定位凸轮轴主动齿轮 (1) 。 安装垫圈 (3) 和螺栓 (4) 。 手动拧紧螺栓 (4) 。
- 从定时位置卸下曲轴定时销。
- 向后转动飞轮大约20度。
注: 如果转动凸轮轴超过20度,活塞和气门之间可能存在干扰。
- 沿正常发动机旋向转动飞轮,直到曲轴正时销可以重新装入曲轴。 本步骤将正时齿轮的齿隙保持在正常发动机旋向。
注: 如果错过曲轴定时销的位置,不要转动飞轮。 如果错过曲轴正时销的位置,请重复步骤7和步骤8。
- 为防止曲轴转动,请接合手摇盘车总成。 将锁定导管拧紧至扭矩 270 ± 25 N·m (200 ± 18 lb ft)。
- 卸下凸轮轴定时销和曲轴定时销。
- 使用工具 (A) 将螺栓 (4) 拧紧至扭矩 2000 ± 275 N·m (1480 ± 200 lb ft)。
- 使用橡皮锤小心地敲击螺栓 (4) 。 重复进行步骤11。 重复此步骤直到扭矩不再变化。
- 松开手动盘车总成上的锁止导向。 确认曲轴和凸轮轴之间的关系。 这可以通过安装定时销来实现。 如果两个定时销都不能安装,请拧松螺栓 (4) 和凸轮轴主动齿轮 (1) 。 重复凸轮轴主动齿轮的安装步骤。
- 拆下曲轴正时销钉和凸轮轴正时销钉。 将正时销装回正确的保存位置。
- 将后凸轮轴检查盖安装在发动机的侧面。
- 调整阀门间隙和燃油定时。
End By: 安装磁电机。 请参阅 拆解和装配磁电机, "- 安装"。
Caterpillar Information System:
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Transmitters
G3606 and G3608 Engines Camshaft Drive Gear - Remove
G3408 and G3412 Engines Engine Oil Pressure Indicator
G3304 and G3306 Engines Water Temperature Indicator
G3408 and G3412 Engines Ammeter
G3304 and G3306 Engines Overspeed Contactor
G3408 and G3412 Engines Voltage Control Relay
G3408 and G3412 Engines Service Meter
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Solenoid Valves
G3408 and G3412 Engines Circuit Breakers
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Electric Motor (Gearbox Oil Pump)
G3408 and G3412 Engines Pressure Switch
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Switches
Electric Protection System Energize-To-Shutoff (ETS) For Generator Set, Industrial and Marine Diesel Engines Troubleshooting the ETS Full Protection System (OP, WT, OS)
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Disassemble
G3606 and G3608 Engines Idler Gears (Rear) - Remove
G3606 and G3608 Engines Idler Gears (Rear) - Install
G3408 and G3412 Engines Ignition System
G3408 and G3412 Engines Air Inlet and Exhaust System
G3606 and G3608 Engines Idler Gears (Front) - Remove
G3606 and G3608 Engines Idler Gears (Front) - Install
G3606 and G3608 Engines Magnetic Pickup - Remove and Install
G3606 and G3608 Engines Housing (Front) - Remove