WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY Caterpillar


WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY

Usage:

WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY

CONFIDENTIAL TIBU3680-00

TECHNICAL INFORMATION BULLETIN

AUGUST 21, 2002

ENGINES

ALL ELECTRONIC MARINE ENGINES EQUIPPED WITH MARINE POWER DISPLAY

 

Component Code 7450

SUBJECT: CONNECTIONS FOR THE MARINE POWER DISPLAY

PROBLEM:

In the Service Manual, SENR5002-03, Installation Guide For Marine Engine Electronic Displays, Illustration 38 is not correct. The wiring for the Alarm Relay is shown incorrectly. Illustration 38 shows the connections for the Marine Power Display.

SOLUTION:

The corrected Illustration 38 follows. The correct illustration will be included in the next revision of the service manual.

 

 

Illustration 38
Connect pin 1 to pin 3 for STBD display. Connect pin 1 and pin 2 to pin 3 for center display. Connect pin 2 to pin 3 for PORT display.

 

 

COPYRIGHT 2002 CATERPILLAR
ALL RIGHTS RESERVED

Caterpillar Information System:

Cracks have been found in the radome of the 167-8930 GPS Antenna and the 194-8015 GPS Antenna Cracks have been found in the radome of the 167-8930 GPS Antenna and the 194-8015 GPS Antenna
TIMING CALIBRATION HARNESS TIMING CALIBRATION HARNESS
3406E Marine Software May Need to be Reinstalled 3406E Marine Software May Need to be Reinstalled
Some Of The Tees In Some Breather Groups May Be Damaged By Normal Operation Some Of The Tees In Some Breather Groups May Be Damaged By Normal Operation
INACCURATE INDICATION OF TRANSMISSION OIL PRESSURE INACCURATE INDICATION OF TRANSMISSION OIL PRESSURE
Oil Leaks From Oil Pan And/Or Crankshaft Rear Seal Carrier Oil Leaks From Oil Pan And/Or Crankshaft Rear Seal Carrier
ETHER START AID OPERATION ETHER START AID OPERATION
Product Link Modules Are Not Reporting Events or Fuel Consumption Product Link Modules Are Not Reporting Events or Fuel Consumption
ELECTRONIC ENGINE CONTROL SOFTWARE ELECTRONIC ENGINE CONTROL SOFTWARE
EXHAUST MANIFOLD GASKET EXHAUST MANIFOLD GASKET
Marine Power Display (MPD) Configuration Changes Accompany Release of 217-8181 MPD Flash File Marine Power Display (MPD) Configuration Changes Accompany Release of 217-8181 MPD Flash File
Inspect the Check Valve in the Fuel Filter Base if You Have Starting Problems or if the Engine Runs Rough Inspect the Check Valve in the Fuel Filter Base if You Have Starting Problems or if the Engine Runs Rough
PREMATURE INLET AND/OR EXHAUST VALVE FAILURE PREMATURE INLET AND/OR EXHAUST VALVE FAILURE
Updated Predelivery/Revisit Checklists Are Now Used Updated Predelivery/Revisit Checklists Are Now Used
REPLACEMENT OF THE FUEL RATIO CONTROL DIAPHRAGM REPLACEMENT OF THE FUEL RATIO CONTROL DIAPHRAGM
Exhaust Backpressure Limits For Marine Engines Exhaust Backpressure Limits For Marine Engines
Bypass Schedule May Be Affected when Machine Security System (MSS) Automatically Adjusts to North American Daylight Savings Time Bypass Schedule May Be Affected when Machine Security System (MSS) Automatically Adjusts to North American Daylight Savings Time
Some configuration settings in the Machine Security System (MSS) may change when MSS software release 207-6258 is upgraded to MSS software release 220-6355 Some configuration settings in the Machine Security System (MSS) may change when MSS software release 207-6258 is upgraded to MSS software release 220-6355
THE DIAGNOSTIC CODE 175-4 �ENGINE OIL TEMPERATURE SHORT TO GROUND� MAY BE A RESULT OF OVERCOOLING THE DIAGNOSTIC CODE 175-4 �ENGINE OIL TEMPERATURE SHORT TO GROUND� MAY BE A RESULT OF OVERCOOLING
FUEL TEMPERATURE COMPENSATION FOR C-15 OPERATING IN NEW HOLLAND FX58 FORAGE HARVESTERS FUEL TEMPERATURE COMPENSATION FOR C-15 OPERATING IN NEW HOLLAND FX58 FORAGE HARVESTERS
Installation Of The Sitevision GPS Cable Encoder Bracket On Hydraulic Excavators Installation Of The Sitevision GPS Cable Encoder Bracket On Hydraulic Excavators
Resetting The G3600 MIDS Control Panel Display Resetting The G3600 MIDS Control Panel Display
Fleet/Key Configuration Issue Using Cat ET Version 2002B Fleet/Key Configuration Issue Using Cat ET Version 2002B
After Software Is Flashed to the Marine Power Display (MPD), the MPD May Lose Graphical Display After Software Is Flashed to the Marine Power Display (MPD), the MPD May Lose Graphical Display
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.