Track Roller - Assemble
Assembly Procedure
Show/hide table
Required Tooling     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 383-1436     | Duo-Cone Seal Installer As     | 1     |
Note: Cleanliness is an important factor. Before the assembly procedure, the exterior of the component must be cleaned.
Note: The rubber toric and all the surfaces containing the rubber toric must be clean and dry at assembly. Apply a thin film of oil to the contact surfaces to the metal seal rings prior to assembly. Seal rings must be assembled square with the bore and the toric seal must not be bulged or twisted.
- User Tooling (A) to install duo-cone seal (11) onto collar (9) .
Show/hide table
Illustration 1 | g03166507 |
- Install O-ring seals (8) to shaft (4) .
Show/hide table
Illustration 2 | g03138541 |
- Install collar (9) and roll pin (10) to shaft (4) .
- User Tooling (A) to install duo-cone seal (7) onto collar (5) .
Show/hide table
Illustration 3 | g03167636 |
- User Tooling (A) to install duo-cone seal (11) to both ends of track roller assembly (1) .
Show/hide table
Illustration 4 | g03167656 |
- Install shaft (4) into track roller assembly (1) .
Show/hide table
Illustration 5 | g03167676 |
- Install collar (5) and roll pin (2) to shaft (4) .
Show/hide table
Illustration 6 | g03167677 |
- Add 180 ± 20 mL (6 ± 0.7 oz) of 8C-3698 Oil to track roller assembly (1) .
- Install plug (3). Tighten plug (3) to a torque of 15 ± 3 N·m (133 ± 27 lb in).
Caterpillar Information System:
PM-200 Cold Planer Machine Systems Track Roller - Disassemble
PM-200 Cold Planer Machine Systems Track Roller - Install
PM-200 Cold Planer Machine Systems Track Roller - Remove
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Hydraulic System Oil Filters - Replace
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Starting Aid (Air Inlet Heater) - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Turbocharger - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Assemble
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Disassemble
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Remove and Install
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Hydraulic System Oil Filters - Replace
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Refrigerant Condenser - Remove and Install
Command for Underground Glossary of Terms
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Muffler - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Refrigerant Compressor - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Machine Preheater - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Engine - Remove and Install
Comfort Series Seat For Caterpillar Machines Optimized Seat Controls
Contour Series Seat Troubleshooting Chart
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Cylinder - Remove and Install
725C2 Articulated Truck Camera
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Pump and Motor - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Single Secondary Fuel Filter Base
2011/04/01 A Troubleshooting Procedure Is Available for Implement Check and Relief Valve Group on Certain M and M Series 2 Motor Graders {4300, 5050}
2011/04/19 Updated Demand Fan Recalibration Information Available for Landfill Compactor, Wheel Dozer, and Wheel Loader Machines {1386, 1387}