Hood Tilt Pump and Motor - Remove and Install
Removal Procedure
Note: The removal and installation of the hood actuators will be performed with the hoods in the DOWN position.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes.
Show/hide table
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death. Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder. |
- Move the battery disconnect switch to the OFF position.
- Remove bolts (2) and open access door (1) .
Show/hide table
Illustration 1 | g02480840 |
- Disconnect hose assemblies (3) at tee connection (4). Disconnect harness assembly (5) .
Show/hide table
Illustration 2 | g01133888 |
- Disconnect harness assembly (7). Disconnect ground strap (9). Remove bolts (8). Remove pump group (6) .
Show/hide table
Illustration 3 | g01133914 |
Installation Procedure
- Install hood tilt pump and motor (6) in the reverse order of removal.
Caterpillar Information System:
725C2 Articulated Truck Camera
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Cylinder - Remove and Install
Contour Series Seat Troubleshooting Chart
Comfort Series Seat For Caterpillar Machines Optimized Seat Controls
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Engine - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Machine Preheater - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Refrigerant Compressor - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Muffler - Remove and Install
PM-200 Cold Planer Machine Systems Track Roller - Assemble
PM-200 Cold Planer Machine Systems Track Roller - Disassemble
PM-200 Cold Planer Machine Systems Track Roller - Install
PM-200 Cold Planer Machine Systems Track Roller - Remove
C4.4 Industrial Engine Fuel Filter Base - Single Secondary Fuel Filter Base
2011/04/01 A Troubleshooting Procedure Is Available for Implement Check and Relief Valve Group on Certain M and M Series 2 Motor Graders {4300, 5050}
2011/04/19 Updated Demand Fan Recalibration Information Available for Landfill Compactor, Wheel Dozer, and Wheel Loader Machines {1386, 1387}
SC-57 Felling Head Felling Head Piston Motor (Disc Saw)
924K, 930K and 938K Wheel Loaders Drive Shaft Spline - Lubricate - If Equipped
Field Installation of the 364-1356 Quick Coupler Conversion Kit (Hydraulic){6129} Field Installation of the 364-1356 Quick Coupler Conversion Kit (Hydraulic){6129}
2011/05/20 New Fuel Water Separator Bowls are Now Used on Certain Caterpillar Equipment {1261, 1263}
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Exhaust Elbow - Remove and Install
2011/03/29 New Water Temperature Regulator for C6.6 and C4.4 Machine Engines {1355, 1380, 1393}
14M and 16M Motor Graders Braking and Hydraulic Fan System Oil Cooler (Brake, Hydraulic Fan) - 14M
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Oil Filter (Rear Axle Lubrication)
584 and 584HD Forwarders Expandable Pin - Tighten