Track Roller - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 8S-7641 | Tubes | 2 |
| 4C-6486 | Stands | 2 | |
Note: The following procedure requires two people.
- Install track roller (9) and bolts (10) .
Show/hide table
 | |
| Illustration 1 | g02480501 |
- Tighten and clean fitting (8). Refer to Operation and Maintenance Manual for the correct procedure to tighten the track.
Show/hide table
 | |
| Illustration 2 | g02480500 |
- Start the engine.
- While pressing switch (5) downward, lift the track assembly with a suitable lifting device.
Note: The suitable lifting device should be able to support at least 1000 kg (2204 lb).
Show/hide table
 | |
| Illustration 3 | g02480496 |
Use the following switches to raise or lower the corresponding track assembly. (5) Switch to raise and lower the left front of the machine. (6) Switch to raise and lower the right front of the machine. (7) Switch to raise and lower the rear of the machine. | |
Show/hide table
 | |
| Illustration 4 | g01449940 |
- Remove the chain supporting the leg.
Show/hide table
 | |
| Illustration 5 | g03138038 |
- Lower the track assembly and the suitable lifting device simultaneously.
- Use switches (5) and (6) to raise the machine off Tooling (A) .
Show/hide table
| | |
| Illustration 6 | g02480496 |
- Remove Tooling (A) .
Show/hide table
 | |
| Illustration 7 | g02480497 |
- Install work light connector (3) and the nut to the side of the machine.
Show/hide table
 | |
| Illustration 8 | g02480476 |
- Raise the rear of the machine and disengage service supports (2) .
Show/hide table
 | |
| Illustration 9 | g03139837 |
- Turn switch (1) to the OFF position.
Show/hide table
 | |
| Illustration 10 | g03139836 |
Caterpillar Information System:
PM-200 Cold Planer Machine Systems Track Roller - Remove
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Hydraulic System Oil Filters - Replace
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Starting Aid (Air Inlet Heater) - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Turbocharger - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Assemble
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Disassemble
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Reversible Fan - Remove and Install
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Hydraulic System Oil Filters - Replace
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Refrigerant Condenser - Remove and Install
Command for Underground Glossary of Terms
Command for Underground Gate Proximity Switch - Test
Command for Underground Sensor (LADAR) - Configure - Area Isolation System (AIS)
PM-200 Cold Planer Machine Systems Track Roller - Disassemble
PM-200 Cold Planer Machine Systems Track Roller - Assemble
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Muffler - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Refrigerant Compressor - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Machine Preheater - Remove and Install
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Engine - Remove and Install
Comfort Series Seat For Caterpillar Machines Optimized Seat Controls
Contour Series Seat Troubleshooting Chart
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Cylinder - Remove and Install
725C2 Articulated Truck Camera
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood Tilt Pump and Motor - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Single Secondary Fuel Filter Base