Water Temperature Regulator - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将冷却液从冷却系统中排入适当的容器至液位低于水温调节器,以便保存或废弃这些冷却液。 有关正确的排放步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 松开上部散热器软管上的软管卡箍,将上部散热器软管从水温调节器壳体 (2) 上断开。
Show/hide table
图 1 | g01985853 |
典型示例 |
- 从水温调节器壳体 (2) 上卸下螺栓 (1) 。
- 将水温调节器壳体 (2) 从缸盖上卸下。
注: 记录水温调节器壳体的朝向。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保水温调节器壳体 (2) 的所有部件清洁且无磨损和损坏。 如果水温调节器的任何部件磨损或损坏,必须更换整个组件。
Show/hide table
图 2 | g01985853 |
典型示例 |
- 检查水温调节器是否正常工作。 请参阅系统操作、测试和调整, "水温调节器 - 测试",以了解测试水温调节器的步骤。 如果水温调节器工作不正确,必须更换整个组件。
- 将水温调节器壳体 (2) 安装到缸盖上。
注: 确保水温调节器壳体的朝向正确。
- 安装螺栓 (1) 。 拧紧螺栓至扭矩为 22 N·m (195 lb in)。
- 连接散热器上软管,然后拧紧软管夹。
- 加注冷却系统至正确液位。 请参阅操作和保养手册, "冷却系统冷却液 - 检查"和操作和保养手册, "冷却系统冷却液 - 更换"以了解正确的加注步骤。
Caterpillar Information System:
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install
C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
773G and 775G Off-Highway Truck Power Train Differential
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Exhaust Pipe
C6.6 Industrial Engine Flywheel - Remove
773G and 775G Off-Highway Truck Power Train Axle Mounting (Rear)
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove
C6.6 Industrial Engine Crankshaft Rear Seal - Install
C27 and C32 Engines for Caterpillar Built Machines Coolant Level Is Low
D11T Track-Type Tractor MID 082 - CID 1326 - FMI 02
C27 and C32 Engines for Caterpillar Built Machines Fan Drive
Cat® Terrain for Drilling User Guide for Drill Operator Declaration of Conformity
C6.6 Industrial Engine Flywheel Housing - Remove and Install - Standard Housing
CAESultra Glossary