Engine Oil Filter Base - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-8760 | Chain Wrench | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Place a suitable container below engine oil filter (5) in order to catch any oil that might be spilled.
- Use Tooling (A) to remove engine oil filter (5). Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
- Remove bolts (3).
Note: If bolts of different lengths are installed, identify the correct position of the bolts.
- Remove engine oil filter base (4).
- Remove gasket (6).
- If necessary, remove plug (1) from engine oil filter base (4). Remove O-ring seal (2) from plug (1).
Show/hide table
Illustration 1 | g01980935 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean engine oil filter base (4). Clean the gasket surfaces of the cylinder block or the engine oil cooler.
- If necessary, install new O-ring seal (2) to plug (1). Install plug (1) to engine oil filter base (4). Tighten the plug to a torque of
12 N·m (106 lb in) . - Install bolts (3) to engine oil filter base (4).
- Install a gasket (6) onto bolts (3). Install the assembly of the engine oil filter base to the cylinder block or the engine oil cooler.
- Tighten bolts (3) to a torque of
22 N·m (195 lb in) . - Install a new engine oil filter (5) and check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.
Show/hide table
Illustration 2 | g01980935 |
Caterpillar Information System:
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Engine Oil and Filter - Change
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Is Low
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Is Restricted
773G and 775G Quarry Trucks Braking System Diagnostic Code List
773G and 775G Off-Highway Truck Mirror
773G and 775G Off-Highway Truck Engine Exhaust (Diverter) - If Equipped
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
773G and 775G Off-Highway Truck Power Train Differential
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Temperature Regulator - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Exhaust Pipe
C6.6 Industrial Engine Flywheel - Remove