Water Pump - Remove and Install
Specifications
Show/hide table
Illustration 1 | g01183807 |
Tightening sequence |
Tighten the bolts in the numerical sequence that is shown in illustration 1 to the following torque. ... 22 N·m (16 lb ft)
Removal Procedure
- Refer to Operation and Maintenance Manual, "Cooling System Coolant - Drain" for the correct filling and draining procedure.
- Disconnect the hose from water pump (3) . Remove bolts (4) . The bolts are different lengths. Note the positions of the different bolts.
Note: Do not remove bolts (7) at this time.
Show/hide table
Illustration 2 | g01626273 |
- Remove water pump (3) from front cover (1) . Remove gasket (2) .
- If necessary, remove bolts (7) , bolts (6) , and gasket (5) from water pump (3) .
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Bolt M8 - by 80 mm     |
2     |
- If necessary, install gasket (5) , cover (6) , and bolts (7) to water pump (3) . Install bolts (7) to cover (6) . Tighten the bolts finger tight at this time.
Show/hide table
Illustration 3 | g01626273 |
Typical Example |
- Clean the mating surface of front cover (1) .
- Install Tooling (A) .
Show/hide table
Illustration 4 | g01626411 |
- Use Tooling (A) in order to install new gasket (2) to the front cover.
- Align water pump (3) with Tooling (A) . Install water pump (3) to front cover (1) .
Note: Ensure that the gear of water pump (5) and the gear of the fuel injection pump mesh.
- Install bolts (4) . Refer to Illustration 3. Tighten bolts (4) finger tight.
Note: Ensure that bolts of different lengths are installed in the correct positions.
- Remove Tooling (A) and install remaining bolts (4) finger tight.
- Tighten bolts (4) and bolts (7) to a torque of 22 N·m (16 lb ft). Tighten the bolts in the sequence that is shown in Illustration 5.
Show/hide table
Illustration 5 | g01515157 |
Tightening sequence for the water pump |
- Install the hose to the water pump (3) .
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the proper filling procedure.
Caterpillar Information System:
430E Backhoe Loader Fan - Remove and Install
785D OEM Off-Highway Truck Power Train Gear Pump (Transmission) - Assemble
785D OEM Off-Highway Truck Power Train Gear Pump (Transmission) - Disassemble
430E Backhoe Loader Alternator - Remove and Install
785D OEM Off-Highway Truck Power Train Gear Pump (Transmission) - Install
785D OEM Off-Highway Truck Power Train Gear Pump (Transmission) - Remove
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Relief Valve (Line) - Test and Adjust
785D OEM Off-Highway Truck Power Train Transmission Hydraulic Control - Assemble
785D OEM Off-Highway Truck Power Train Transmission Hydraulic Control - Disassemble
2008/08/25 A New Rocker Arm Assembly is Available {1123}
2008/08/25 A New Rocker Arm Assembly is Available {1123}
2008/09/08 An Improved Pressure Switch is Now Available {1435}
MINEGEM Machine Control ; Guidance Products General Hazard Information
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Pump Control Valve - Power Compensator
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Hydraulic and Steering System Control Manifold (Outlet)
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold and Solenoid (Boom, Stick, Pattern Switch)
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold and Solenoid (Inlet)
2010/08/25 A New Air Dryer is Available {1803, 4285}
430E Backhoe Loader Water Temperature Regulator - Remove and Install
PL61 Pipelayer Machine Systems Accumulator - Remove and Install
785D OEM Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Remove
785D OEM Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Install
785D OEM Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Disassemble
430E Backhoe Loader Stick - Remove and Install