Illustration 1 | g01462669 |
Note: All bores must be free of paint. Use the 5P-0960 Grease Cartridge in order to coat all bores for the pins, the stick, the upper frame and the cylinder pin bores.
(1) 235-7527 Sleeve Bearing
- Quantity ... 2
- Inside diameter ...
110.30 ± 0.04 mm (4.343 ± 0.002 inch) - Outside diameter ...
130.240 ± 0.013 mm (5.1275 ± 0.0005 inch) - Installation depth of the sleeve bearing ...
9.5 ± 0.8 mm (0.37 ± 0.03 inch) - Inside diameter ...
(2) 4I-4619 Pin As
- Pin diameter ...
89.850 ± 0.025 mm (3.5374 ± 0.0010 inch)
- Bore diameter for the pin assembly ...
90.043 ± 0.043 mm (3.5450 ± 0.0017 inch)
(3) As required, use the 093-0122 Shim in order to adjust the maximum lateral clearance to
- Quantity ... 6
- Thickness of one shim ...
2 mm (0.1 inch) - Thickness of one shim ...
(4) 130-8818 Pin
- Pin diameter ...
99.850 ± 0.040 mm (3.9311 ± 0.0016 inch) - Bore diameter for the pin ...
100.043 ± 0.043 mm (3.9387 ± 0.0017 inch) - Bore diameter for the pin ...
(5) 121-8702 Pin As
- Pin diameter ...
99.850 ± 0.040 mm (3.9311 ± 0.0016 inch) - Bore diameter for the pin assembly ...
100.043 ± 0.043 mm (3.9387 ± 0.0017 inch) - Bore diameter for the pin assembly ...
(6) As required, use the following shims in order to adjust the maximum lateral clearance to
- Quantity ... 2
- Thickness of one shim ...
1.0 mm (0.04 inch) - Thickness of one shim ...
093-0084 Shim
- Quantity ... 1
- Thickness of the shim ...
1.6 mm (0.06 inch) - Thickness of the shim ...
7Y-2497 Shim
- Quantity ... 1
- Thickness of the shim ...
2 mm (0.1 inch) - Thickness of the shim ...
093-0116 Shim
(7) As required, use the following shims in order to adjust the maximum lateral clearance to
- Quantity ... 2
- Thickness of one shim ...
1.0 mm (0.04 inch) - Thickness of one shim ...
093-0090 Shim
- Quantity ... 1
- Thickness of the shim ...
1.6 mm (0.06 inch) - Thickness of the shim ...
7Y-3355 Shim
- Quantity ... 1
- Thickness of the shim ...
2 mm (0.1 inch) - Thickness of the shim ...
093-0122 Shim
(8) Lubricate the sealing lip of two lip type seals lightly with the lubricant that is being sealed during assembly.
Illustration 2 | g01468408 |
Note: Use the 5P-0960 Grease Cartridge in order to fill with grease through the grease fitting (10) after mounting the pin at the boom foot. Before installing the pipe plug (9), make sure that the grease flows out of the pipe plug hole.
Illustration 3 | g01508573 |
Section B-B |
(11) 093-0366 Spacer
- Quantity ... 1
- Thickness of the spacer ...
12 mm (0.5 inch) - Thickness of the spacer ...