Oscillating Axle (Rear) - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Use a suitable lifting device to position oscillating axle (8). The weight of oscillating axle (8) is approximately 1225 kg (2700 lb).
Show/hide table
 | |
| Illustration 1 | g01181134 |
- Install bolts (9) and (10). The torque for bolts (9) and (10) is 475 ± 60 N·m (350 ± 45 lb ft).
Show/hide table
 | |
| Illustration 2 | g01181135 |
Show/hide table
 | |
| Illustration 3 | g01181136 |
- Connect tube assembly (6) to axle support (7). Repeat this Step for the opposite side.
Show/hide table
 | |
| Illustration 4 | g01181133 |
- Install clips (5) and connect hose assembly (4) .
Show/hide table
 | |
| Illustration 5 | g01181132 |
- Connect hose assembly (2) and install hose assembly (3) if the machine is equipped with an axle oil cooler.
Show/hide table
 | |
| Illustration 6 | g01181131 |
- Connect harness assembly (1) .
Show/hide table
 | |
| Illustration 7 | g01181130 |
- Refill the oscillating axle with clean oil. Refer to Operation and Maintenance Manual, "Refill Capacities".
End By:
- Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) - Remove and Install".
- Install the rear tires and the rims. Refer to Disassembly and Assembly, "Tire and Rim (Rear) - Remove and Install".
Caterpillar Information System:
TH350B, TH360B, TH460B and TH560B Telehandlers Hydraulic System Lowering Control Pump (Electric) - If Equipped
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Oscillating Axle (Rear) - Remove
RM-300 Reclaimer Mixer Machine Systems Sequence Valve - Test and Adjust
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic Oil Sample - Obtain
2005/07/25 Correction to Systems Operation Testing and Adjusting, "Axle Oil Cooler" {1365, 1408}
2005/07/18 Correction to Specifications, "Pressure Switch (Residual Brake Oil)" {1408}
2005/07/04 Correction to Specifications, "Pressure Switch (Axle Oil)" {1408}
966H Wheel Loader and 972H Wheel Loader Power Train Oil Filter (Power Train)
RM-300 Reclaimer Mixer Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
RM-500 Road Reclaimer/Soil Stabilizer Power Train Piston Motor (Front Propel) - Assemble
RM-500 Road Reclaimer/Soil Stabilizer Power Train Piston Motor (Front Propel) - Disassemble
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Fuel System Water Separator - Drain
966H Wheel Loader and 972H Wheel Loader Power Train Modulating Valve (Transmission Clutch)
2006/01/02 Improvements to the Output Transfer Gear {3159}
RM-300 Reclaimer Mixer Machine Systems Gear Pump (Transmission) Flow - Test - Rotor Differential
2006/01/02 Improvements to the Output Transfer Gear {3159}
AP-800D and BG-230D Asphalt Pavers Lubricant Viscosities
793C Off-Highway Truck Automatic Lubrication Reservoir - Fill
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Piston Motor (Drum Propel) - Disassemble
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Piston Motor (Drum Propel) - Assemble
789C Off-Highway Truck Fuel System Priming Filter - Replace - If Equipped
789C Off-Highway Truck Oil Filter (Torque Converter) - Replace
2005/07/04 An Improved Hoist Control Valve Is Available {5051, 5136}
RM-300 Reclaimer Mixer Machine Systems Wheel Alignment (Front) - Check and Adjust