Piston Motor (Drum Propel) - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
C | 2S-8229 | Adapter | 1 |
1U-9895 | Crossblock | 1 | |
5P-5213 | Adapter | 1 | |
D | 8H-8581 | Feeler Gauge | 1 |
E | - | Mobil SHC Gear Grade 680 (Mobil product #61095-6) | 90 ml |
- Install Duo-Cone seal (28) and bearing cone (29).
Show/hide table
Illustration 2 g01181440 - Install bearing cup (27).
- Repeat Step 2 for the opposite side.
Show/hide table
Illustration 3 g01181815 - Raise the temperature of bearing cone (26).
- Install shaft (25) into housing (24).
- Install bearing cone (26).
Show/hide table
Illustration 4 g01181873 - Use Tooling (C) and a suitable press to apply 4 tons of pressure to bearing cone (26).
- Install keepers (21).
- Use Tooling (D) to measure the distance between keepers (21) and bearing cone (26).
- Remove keepers (21) and Tooling (C).
Show/hide table
Illustration 5 g01181435 - Install shim (23).
Show/hide table
Illustration 6 g01181433 - Install keepers (21) and O-ring seal (22).
Show/hide table
Illustration 7 g01181432 - Install cylinder (20), shaft (19), and housing (18).
Show/hide table
Illustration 8 g01181431 - Install O-ring seal (17).
Show/hide table
Illustration 9 g01181430 - Install housing (16), bolts (15), O-ring seals (14), and plug (13).
Show/hide table
Illustration 10 g01181428 - Install housing (11), bolts (8), plates (12), plates (10), and seal (9).
Show/hide table
Illustration 11 g01625634 (A) 41.0 ± 0.1 mm (1.6142 ± 0.0039 inch) - Install shims (7) to acquire dimension (A).
Show/hide table
Illustration 12 g01181427 - Install ring (6).
Show/hide table
Illustration 13 g01181818 - Install piston (5), bevel washer (3), and gasket (4).
Show/hide table
Illustration 14 g01181425 - Install bolts (1) and cover (2).
Show/hide table
Illustration 15 g06210726 - Fill cavity (X) with Tooling (E).
Show/hide table
Illustration 1 | g01181442 |
End By:
- Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Drum Propel) - Remove".
Caterpillar Information System:
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Piston Motor (Drum Propel) - Disassemble
793C Off-Highway Truck Automatic Lubrication Reservoir - Fill
AP-800D and BG-230D Asphalt Pavers Lubricant Viscosities
2006/01/02 Improvements to the Output Transfer Gear {3159}
RM-300 Reclaimer Mixer Machine Systems Gear Pump (Transmission) Flow - Test - Rotor Differential
2006/01/02 Improvements to the Output Transfer Gear {3159}
966H Wheel Loader and 972H Wheel Loader Power Train Modulating Valve (Transmission Clutch)
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Oscillating Axle (Rear) - Install
TH350B, TH360B, TH460B and TH560B Telehandlers Hydraulic System Lowering Control Pump (Electric) - If Equipped
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Oscillating Axle (Rear) - Remove
RM-300 Reclaimer Mixer Machine Systems Sequence Valve - Test and Adjust
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic Oil Sample - Obtain
789C Off-Highway Truck Fuel System Priming Filter - Replace - If Equipped
789C Off-Highway Truck Oil Filter (Torque Converter) - Replace
2005/07/04 An Improved Hoist Control Valve Is Available {5051, 5136}
RM-300 Reclaimer Mixer Machine Systems Wheel Alignment (Front) - Check and Adjust
RM-300 Reclaimer Mixer Machine Systems Hydraulic Accumulator (Rotor Transmission Shift Valve) - Test and Adjust
24H Motor Grader Braking System Valve (Service and Secondary Brake Control)
120H and 135H Motor Graders Hydraulic and Steering System Relief Valve (Scarifier)
C15 and C18 Tier 4 Final Engines Vibration Damper - Check
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System IQAN Error Messages and Warnings
C7.1 Engines for Caterpillar Built Machines Camshaft
RM-300 Reclaimer Mixer Machine Systems Rotor Clutch - Test and Adjust
C15 and C18 Petroleum Generator Sets Engine Performance - Test - Standby Generator Sets