Piston Motor (Front Propel) - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 136-1452     | 挡圈钳组件     | 1     |
- 冷却旋转总成 (30) 。
Show/hide table
图 1 | g01182025 |
Show/hide table
图 2 | g01181046 |
- 将旋转总成 (30) 安装到壳体 (31) 中。
- 安装隔套 (29) 。
- 使用工具 (A) 安装挡圈 (28) 。
- 使用适当的压具将旋转总成 (30) 压在挡圈 (28) 上。
- 安装密封垫 (27) 。
- 安装壳体 (25) 和螺栓 (26) 。
Show/hide table
图 3 | g01181043 |
- 安装 O 形密封圈 (23) 。
- 使用工具 (A) 安装挡圈 (24) 。
- 安装密封件 (22) 。
Show/hide table
图 4 | g01181042 |
- 安装盖 (21) 。
Show/hide table
图 5 | g01181041 |
- 使用工具 (A) 安装挡圈 (20) 。
- 安装销 (18) 和轴承 (19) 。
Show/hide table
图 6 | g01181040 |
- 安装十字轴组件 (17) 。
Show/hide table
图 7 | g01181039 |
- 安装轴承 (15) 、柱塞筒 (16) 和孔板 (14) 。
Show/hide table
图 8 | g01181038 |
- 安装板 (13) 。
Show/hide table
图 9 | g01181037 |
- 安装 O 形密封圈 (11) 和活塞 (12) 。
Show/hide table
图 10 | g01181036 |
- 安装盖 (10) 和螺栓 (9) 。
Show/hide table
图 11 | g01181035 |
- 安装滑阀 (6) 。
Show/hide table
图 12 | g01181034 |
- 安装护圈 (7) 和弹簧 (8) 。
- 安装螺塞 (5) 。
Show/hide table
图 13 | g01181033 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装螺塞 (4) 。
- 对于另一侧重复步骤 20 至步骤 21。
- 安装密封垫 (3) 。
Show/hide table
图 14 | g01181032 |
- 安装盖 (2) 和螺栓 (1) 。
Show/hide table
图 15 | g01181031 |
End By: 安装活塞马达。 请参阅 拆解和组装, "活塞马达 - 安装"。
Caterpillar Information System:
RM-500 Road Reclaimer/Soil Stabilizer Power Train Piston Motor (Front Propel) - Disassemble
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Fuel System Water Separator - Drain
2005/07/04 New Gaskets for the Turbocharger Oil Lines are Now Used {1052, 1307}
2005/07/18 Governor Cable Assembly Is Improved {1265}
RM-300 Reclaimer Mixer Engine Supplement Alternator - Remove and Install
RM-300 Reclaimer Mixer Machine Systems Relief Valve (Hood Tilt) - Test and Adjust
C6.6 Engines for Caterpillar Built Machines Cylinder Block
RM-300 Reclaimer Mixer Machine Systems Relief Valve (Parking Brake/Transmission Hydraulic Control) - Test and Adjust
AccuGradeTM - Grade Control System (GPS/ATS/Sonic/Cross Slope) Light Bar
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Differential and Bevel Gear - Install
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Differential and Bevel Gear - Remove
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Fuel System Filter and Water Separator - Replace
RM-300 Reclaimer Mixer Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
966H Wheel Loader and 972H Wheel Loader Power Train Oil Filter (Power Train)
2005/07/04 Correction to Specifications, "Pressure Switch (Axle Oil)" {1408}
2005/07/18 Correction to Specifications, "Pressure Switch (Residual Brake Oil)" {1408}
2005/07/25 Correction to Systems Operation Testing and Adjusting, "Axle Oil Cooler" {1365, 1408}
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic Oil Sample - Obtain
RM-300 Reclaimer Mixer Machine Systems Sequence Valve - Test and Adjust
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Oscillating Axle (Rear) - Remove
TH350B, TH360B, TH460B and TH560B Telehandlers Hydraulic System Lowering Control Pump (Electric) - If Equipped
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train Oscillating Axle (Rear) - Install
966H Wheel Loader and 972H Wheel Loader Power Train Modulating Valve (Transmission Clutch)
2006/01/02 Improvements to the Output Transfer Gear {3159}