Rocker Shaft and Pushrod - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install pushrods (5) .
Note: Ensure that the pushrods are installed in the original location and that the pushrods are seated in the valve lifters correctly.
Show/hide table
Illustration 1 | g01035051 |
- Loosen the nut and adjustment screw (1) on each rocker arm to prevent bending a valve or a pushrod during the installation.
Show/hide table
Illustration 2 | g01035049 |
- Position rocker shaft assembly (3) .
- Install bolts (2) and tighten to a torque of 10 to 20 N·m (89 to 177 lb in).
- Install bolts (4) and tighten to a torque of 10 to 20 N·m (89 to 177 lb in).
- Final torque for the nut on adjustment screw (1) is 20 N·m (177 lb in)
- Adjust the inlet valve lash and the exhaust valve lash to 0.250 mm (0.0098 inch). Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
988H Wheel Loader Engine Oil and Filter - Change
988H Wheel Loader Engine Oil Level - Check
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C-9 Engine for the 973C Track-Type Loader Electrical Power Supply Circuit - Test
2003/06/23 An Improved Spin-On Oil Filter {1306, 1308}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Drum Group (Smooth and Padded)
143H and 163H Motor Graders Power Train Flushing and Cooling Control Valve - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3054E Engine for Caterpillar Built Machines Cylinder Head - Remove
3054E Engine for Caterpillar Built Machines Cylinder Head - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Remove
143H and 163H Motor Graders Power Train Flushing and Cooling Control Valve - Assemble
PM820, PM822, and PM825 Cold Planer Engine Valve Lash - Check
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group - Remove and Install
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Secondary Steering System
Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000} Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000}
2003/05/26 New Final Drive for the Propel System {4050, 4800, 5467}
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft - Remove and Install
C-9 Engine for the 973C Track-Type Loader E025 High Inlet Air Temperature Derate
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C9 On-highway Engine Water Pump