Camshaft Gear - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-2320     | Combination Puller     | 1     |
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove camshaft gear (4) from camshaft (2) . Remove key (1) and thrust plate (3) .
Note: Do not lose the key from the camshaft gear.
Show/hide table
Illustration 1 | g01993021 |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the camshaft gear, the key, and the thrust plate for wear or damage.
- Install key (1) and thrust plate (3) . Raise the temperature of camshaft gear (4) and install camshaft gear (4) on camshaft (2) .
Note: Ensure that the key is installed on the camshaft. When you install the camshaft gear, ensure that the marked teeth are facing toward the front. If necessary, tap the gear with a soft hammer in order to seat the key in the keyway.
Show/hide table
Illustration 2 | g01993021 |
End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Caterpillar Information System:
C-9 Engine for the 973C Track-Type Loader E025 High Inlet Air Temperature Derate
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft - Remove and Install
2003/05/26 New Final Drive for the Propel System {4050, 4800, 5467}
Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000} Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000}
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Secondary Steering System
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Install
PM820, PM822, and PM825 Cold Planer Engine Valve Lash - Check
143H and 163H Motor Graders Power Train Flushing and Cooling Control Valve - Assemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C9 On-highway Engine Water Pump
988H Wheel Loader Cooling System Coolant Level - Check
C-9 Engine for the 973C Track-Type Loader E027 High Inlet Air Temperature Warning
2003/06/16 An Updated Air Tank Improves Serviceability for the Ether Starting Aid Cylinder on Certain Motor Graders {1456, 4272}
TH350B, TH355B, TH360B and TH460B Telehandlers Fire Extinguisher Location
C-9 Engine for the 973C Track-Type Loader Throttle Switch Circuit - Test
980G Wheel Loader Bucket Lower Pivot Bearings - Lubricate
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Metering Pump (Steering)
3044C Engine for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
793C Off-Highway Truck Machine Systems Control Valve (Hoist) - Install
2003/06/23 Special Instruction, REHS1638, "Rework Procedure for the Tube Assembly of the yoke" is Available {7050, 7051}