Camshaft - Remove and Install
Removal Procedure
Start By:
- Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
- Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Turn the engine upside-down so the valve lifters are held in a position away from the camshaft.
- Remove bolts (1) .
Show/hide table
Illustration 1 | g01034097 |
- Carefully remove camshaft (2) .
Show/hide table
Illustration 2 | g01034100 |
Show/hide table
NOTICE |
---|
Do not damage the lobes or the bearings when the camshaft is removed or installed. |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil prior to installation.
- Carefully install camshaft (2) .
Show/hide table
Illustration 3 | g01034100 |
Show/hide table
NOTICE |
---|
Do not damage the lobes or the bearings when the camshaft is removed or installed. |
- Install bolts (1). Tighten bolts (1) to a torque of 10 to 13 N·m (7 to 10 lb ft).
Show/hide table
Illustration 4 | g01034097 |
End By:
- Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Caterpillar Information System:
2003/05/26 New Final Drive for the Propel System {4050, 4800, 5467}
Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000} Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000}
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Secondary Steering System
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Install
PM820, PM822, and PM825 Cold Planer Engine Valve Lash - Check
143H and 163H Motor Graders Power Train Flushing and Cooling Control Valve - Assemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
988H Wheel Loader Engine Oil and Filter - Change
988H Wheel Loader Engine Oil Level - Check
C-9 Engine for the 973C Track-Type Loader E025 High Inlet Air Temperature Derate
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C9 On-highway Engine Water Pump
988H Wheel Loader Cooling System Coolant Level - Check
C-9 Engine for the 973C Track-Type Loader E027 High Inlet Air Temperature Warning
2003/06/16 An Updated Air Tank Improves Serviceability for the Ether Starting Aid Cylinder on Certain Motor Graders {1456, 4272}
TH350B, TH355B, TH360B and TH460B Telehandlers Fire Extinguisher Location
C-9 Engine for the 973C Track-Type Loader Throttle Switch Circuit - Test
980G Wheel Loader Bucket Lower Pivot Bearings - Lubricate
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Metering Pump (Steering)
3044C Engine for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install