Engine Oil Level - Check
Show/hide table
| 注意 |
|---|
发动机曲轴箱注油时，油不要过少或过满。 任何一种情况都会造成发动机损坏。 |
- 打开机器左侧的发动机检修门。
Show/hide table
 | |
| 图 1 | g00841382 |
- 取出发动机机油尺 (1) 并用干净的布将其擦干净。 然后，将油尺插入再取出。 这样可以保证较准确地测量出发动机的油位。
Show/hide table
 | |
| 图 2 | g01001056 |
当发动机停止时，油位应保持在油尺的交叉刻度范围 (A) 内。 油尺的这个范围标为"安全起动范围"。
Show/hide table
 | |
| 图 3 | g00999790 |
- 如有必要，拆下机油加注口盖 (2) ，添加机油。 清洁并安装机油加注口盖。
- 关闭发动机检修门。
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C-9 Engine for the 973C Track-Type Loader Electrical Power Supply Circuit - Test
2003/06/23 An Improved Spin-On Oil Filter {1306, 1308}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Drum Group (Smooth and Padded)
143H and 163H Motor Graders Power Train Flushing and Cooling Control Valve - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3054E Engine for Caterpillar Built Machines Cylinder Head - Remove
3054E Engine for Caterpillar Built Machines Cylinder Head - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Support and Vibratory Drive
2003/06/09 Charts for the Altitude Deration of Caterpillar Built Machines that are Powered By 3500 EUI and 3500B Engines {1902, 1923}
988H Wheel Loader Engine Oil (High Speed) and Oil Filter - Change - If Equipped
988H Wheel Loader Engine Oil and Filter - Change
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Remove
143H and 163H Motor Graders Power Train Flushing and Cooling Control Valve - Assemble
PM820, PM822, and PM825 Cold Planer Engine Valve Lash - Check
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group - Remove and Install
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Secondary Steering System
Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000} Installation Instructions for the 212-5949 Machine Conversion Ar on the IT14G Integrated Toolcarrier{670B, 7000}
2003/05/26 New Final Drive for the Propel System {4050, 4800, 5467}
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft - Remove and Install