Washer Pump Assemblies Must Be Primed Properly {7306}
- Caterpillar Products:
- All
The following washer pump assemblies are centrifugal pump assemblies: 7T-8890 Washer Pump As, 7T-8891 Washer Pump As, 6T-1375 Washer Pump As, 117-2826 Washer Pump As and 223-3383 Washer Pump As
Centrifugal pump assemblies are not self-priming. Centrifugal pump assemblies must be primed properly in order to operate correctly. Refer to the following procedure in order to prime a centrifugal pump assembly.
Priming Procedure
- Install the washer pump assembly and install all the hoses.
Show/hide table
Illustration 1 | g00946156 |
(1) Washer pump assembly (2) Outlet hose (3) Inlet hose |
- Fill the reservoir with washer fluid.
- Disconnect pump outlet hose (2) .
- Once fluid flows out of pump assembly (1), connect pump outlet hose (2) .
- The pump is now primed and ready for operation.
Note: If the tank is allowed to run out of fluid, the pump will need to be primed again. Follow Steps 2 through 5 in order to prime the pump.
Note: Use the appropriate antifreeze for temperatures that are below freezing.
Caterpillar Information System:
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Operation
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Work Tool Installation and Removal
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Daily Inspection
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Plate Locations and Film Locations
574B Forwarder Transmission Gearbox Oil Sample - Obtain
574B Forwarder Hydraulic System Oil Sample - Obtain
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Specifications
574B Forwarder Grapple Damper Brake - Inspect/Adjust
574B Forwarder Grapple Damper - Lubricate
574B Forwarder Fuel System Primary Filter - Replace
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Caterpillar Approved Machines
574B Forwarder Fuel System - Prime
2003/01/20 Kits are Available for Servicing 105-4324 Air Starting Motor Gp {1451}
R1300G Load Haul Dump Hydraulic System Main Hydraulic System
R1300G Load Haul Dump Hydraulic System Main Control Valve
R1300G Load Haul Dump Hydraulic System Relief Valve (Lift Circuit)
TH340B, TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Shutoff Valve (Axle Lock) - Remove and Install
TH340B, TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Fuel Tank - Remove
CB-534D and CB-564D Asphalt Compactors Steering Cylinder Ends - Lubricate
3056E Industrial Engine Cylinder Head
TH210 and TH215 Telehandlers Machine Systems Boom Cylinder - Remove and Install
3512 and 3516 EUI Engines and 784B, 785B, 789B and 793B Off-Highway Truck/Tractors Exhaust Bypass Valve
2003/01/06 Use the New 187-0951 Lockup Clutch and Synchronizing Valve on 793C Off-Highway Trucks {3124}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Engine Oil Level - Check