Cylinder Head
Show/hide table
Illustration 1 | g00876966 |
Cylinder head tightening sequence |
Use the following procedure in order to tighten the bolts for the cylinder head:
- Put clean engine oil on the threads of the bolts. The bolts are tightened in the numerical sequence that is shown in Illustration 1.
Tighten the bolts to the following torque. ...
110 N·m (80 lb ft) - Repeat the procedure in Step 1 to ensure that all of the bolts are tightened to the correct torque.
- Use the numerical sequence that is shown in Illustration 1 to tighten the bolts for the additional torque-turn specification.
- Tighten the short bolts (S) for an additional 150 degrees (2.5 flats).
- Tighten the medium sized bolts (M) for an additional 180 degrees (3.0 flats).
- Tighten the long bolts (L) for an additional 210 degrees (3.5 flats).
Cylinder head thickness ...
Minimum permissible thickness after the cylinder head face has been resurfaced. ...
Maximum permissible projection of the fuel injection nozzle below the face of the cylinder head after resurfacing ...
Show/hide table
Illustration 2 | g00295372 |
Checking the distortion of the cylinder head |
Maximum distortion of the cylinder head is given in the following table.
Show/hide table
Dimension | Maximum Permissible Distortion |
Width "A" | |
Length "B" | |
Diagonal "C" | |
Caterpillar Information System:
CB-534D and CB-564D Asphalt Compactors Steering Cylinder Ends - Lubricate
TH340B, TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Fuel Tank - Remove
TH340B, TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Shutoff Valve (Axle Lock) - Remove and Install
R1300G Load Haul Dump Hydraulic System Relief Valve (Lift Circuit)
R1300G Load Haul Dump Hydraulic System Main Control Valve
R1300G Load Haul Dump Hydraulic System Main Hydraulic System
2003/01/20 Kits are Available for Servicing 105-4324 Air Starting Motor Gp {1451}
2002/12/23 Washer Pump Assemblies Must Be Primed Properly {7306}
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Operation
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Work Tool Installation and Removal
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Daily Inspection
PC205, PC206, PC210, PC305B, PC306B, PC306B XD, PC310B, PC310B XD, PC408B and PC412B Cold Planers Plate Locations and Film Locations
TH210 and TH215 Telehandlers Machine Systems Boom Cylinder - Remove and Install
3512 and 3516 EUI Engines and 784B, 785B, 789B and 793B Off-Highway Truck/Tractors Exhaust Bypass Valve
2003/01/06 Use the New 187-0951 Lockup Clutch and Synchronizing Valve on 793C Off-Highway Trucks {3124}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Engine Oil Level - Check
3512 and 3516 EUI Engines and 784B, 785B, 789B and 793B Off-Highway Truck/Tractors Exhaust Bypass Valve
24H Motor Grader Hydraulic and Steering System Accumulator (Blade Cushion)
2002/12/23 Summary of Changes and Updates to CABSWin 1.4 {7600}
2003/01/01 The Color of Certain O-Ring Seals Is Changing {7555}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Changing Direction and Speed
3176C and 3406E Engines for Caterpillar Built Machines E027 High Inlet Air Temperature Warning
2002/12/01 The Color of Certain O-Ring Seals Is Changing {7555}
797B Off-Highway Truck Power Train Machine Preparation for Troubleshooting