Camshaft - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 8S-1378 | 螺柱拆卸器和重装器工具 | 1 |
B | 9S-9082 | 发动机盘车工具 | 1 |
C | 1B-9575 | 螺栓 | 2 |
C | 9M-1974 | 硬垫圈 | 2 |
D | 1P-0510 | 冲头总成 | 1 |
e | 5P-0944 | 定位销拉拔器总成 | 1 |
F | 1P-2321 | 组合式拉拔器 | 1 |
F | 9S-9153 | 拉拔器爪 | 3 |
开始:
- 拆下前壳体。 请参阅拆解和组装, "壳体(前)拆卸"。
- 拆卸挺杆总成。 请参阅拆解和组装, "挺杆总成 - 拆卸和安装"。
- 转动发动机,直到凸轮轴驱动齿轮和惰轮上的正时标记 “V” 对齐。
Show/hide table
图 2 g00832971 - 将两条螺栓 (1) 和板 (2) 从凸轮轴上拆下。
Show/hide table
图 3 g00832973 - 将凸轮轴 (3) 从缸体上拆下。
Show/hide table
图 4 g00832975 - 必要时,利用工具 (D) 和压具拆下凸轮轴驱动齿轮 (4)。
Show/hide table
图 1 | g00572090 |
注: 所有 3408E 发动机均在飞轮壳内配有平衡齿轮。 平衡齿轮由曲轴或凸轮轴驱动。 平衡齿轮具有正时标记。 此正时标记必须与平衡齿轮驱动齿轮上的正时标记对齐。 如果通过飞轮壳可以接近后凸轮轴齿轮,则无需拆卸飞轮壳便可拆下后凸轮轴齿轮。 如果平衡齿轮由曲轴驱动,则拆装凸轮轴后齿轮时无需考虑正时。 如果平衡齿轮由凸轮轴后齿轮驱动,则安装凸轮轴后齿轮时,凸轮轴后齿轮和平衡齿轮上的正时标记必须对齐。 请参阅拆解和组装, "平衡器总成 - 拆卸"和拆解和组装, "平衡器总成 - 安装"。 3412 发动机没有平衡齿轮。 凸轮轴后侧的定位销将后凸轮轴齿轮定位到凸轮轴上。 后凸轮轴齿轮通过四条螺栓固定在凸轮轴上。
- 以下程序适用于具有涡轮增压器放油孔的飞轮壳。 可以通过多个可能位置接近凸轮轴后齿轮。 接近途径取决于飞轮壳。 可能需要拆下端盖。 可能需要拆下涡轮增压器排油管。 如果不存在接近途径,则需要拆下飞轮壳。 请参阅拆解和组装, "飞轮壳体 - 拆卸和安装"。 请参阅本节内的"飞轮壳已经拆下"部分。
注: 如果平衡齿轮由凸轮轴后齿轮驱动,则凸轮轴后齿轮和平衡齿轮上的正时标记必须对齐。 如果平衡齿轮由曲轴驱动,则拆卸凸轮轴后齿轮时无需考虑正时。
Show/hide table图 6 g00832648 (10) 螺柱
(11) 螺栓
(12) 凸轮轴后齿轮 - 拆下涡轮增压器排油管。 利用工具 (A) 拆下螺柱 (10)。
Show/hide table
图 7 g00834273 - 必须转动凸轮轴才能接近螺栓 (11)。 当凸轮轴后齿轮内的螺纹孔与安装涡轮增压器排油管的螺纹孔对齐时,便可拆下最后一条螺栓。 这些小孔应当在发动机位于上止点时对齐。 曲轴每转动两圈,凸轮轴将转动一圈。 在发动机前端查看凸轮轴驱动齿轮和惰轮上的正时标记。 这些正时标记必须对齐才能将工具 (C) 拧入凸轮轴后齿轮中。 利用工具 (B) 转动飞轮,在可以够到时拆下其中的三条螺栓 (11)。
Show/hide table
图 8 g00834303 - 在其他三条螺栓已经拆下且工具 (C) 已拧入凸轮轴后齿轮后,拆下发动机位于上止点时可以够到的螺栓。 当其他三条螺栓已经拆下时,将工具 (C) 拧入凸轮轴后齿轮中。 拆下第四条螺栓 (11)。
注: 拆卸凸轮轴时,必须利用工具 (C) 固定凸轮轴后齿轮。 工具 (C) 将使平衡齿轮与凸轮轴后齿轮间保持啮合状态。
Show/hide table图 9 g00834315 - 通过均匀上紧工具 (C) 从凸轮轴上拆下凸轮轴后齿轮。
Show/hide table
图 10 g00572090 - 检查凸轮轴驱动齿轮和惰轮上的正时标记 (V) 是否对齐。
Show/hide table
图 11 g00833004 - 将两条螺栓 (13) 和板 (14) 从凸轮轴上拆下。
Show/hide table
图 12 g00833007 - 从缸体上拆下凸轮轴 (15)。
Show/hide table
图 13 g00833008 - 必要时,利用工具 (D) 和压具拆下凸轮轴齿轮 (16)。
Show/hide table
图 14 g00834376 - 必要时,利用工具 (E) 将定位销 (20) 从凸轮轴上拆下。
Show/hide table
图 5 | g00832150 |
(5) 飞轮壳体
(6) 涡轮增压器排油孔 (7) 凸轮轴后齿轮 (8) 正时标记 (9) 平衡齿轮 |
- 松开四条螺栓 (17)。 松开螺栓大约
6.4 mm (0.25 in) 。 利用工具 (F) 将凸轮轴后齿轮 (18) 从凸轮轴上松开。 - 拆下工具 (F)。 拆下四条螺栓 (17) 和凸轮轴后齿轮 (18)。
- 请参阅"带凸轮轴后齿轮的发动机"。 采用步骤 6 至步骤 10。
Show/hide table
图 15 | g00832518 |
Caterpillar Information System:
2001/11/19 New Protective Caps For Hose Clamps Are Now Available {5057}
2001/10/15 Proper Adjustment of the Kickout Positioner Improves Reliability {5109, 5112}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0346 - FMI 05
Disassembly and Assembly of the Water Pump on the 3524B Engine{1361} Disassembly and Assembly of the Water Pump on the 3524B Engine{1361}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
SR4 Generator with VR3 or VR4 Voltage Regulator Rotating Rectifier - Test
966G Series II and 972G Series II Wheel Loaders Engine Supplement Crankshaft Front Seal - Remove - Engine in Chassis
CP-563C and CS-563C Vibratory Compactors Cab Tilting
CP-563C and CS-563C Vibratory Compactors Lifting and Tying Down the Machine
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader E190 Engine Overspeed Warning
TL5 Series Field Cultivator Safety Signs and Labels
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Pressure Switch (Retarder)
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Gear Pump (Hoist) - Remove
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Pressure Switch (Automatic Retarder)
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Gear Pump (Hoist) - Install
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Piston Pump (Steering) - Remove
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Final Drive Planetary (Drum) Oil - Check
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Stopping the Engine if an Electrical Malfunction Occurs
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Piston Pump (Steering) - Install
Topcon® System Five Part Number Location
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0346 - FMI 06
CS-531D, CP-533D and CS-533D Vibratory Compactors Engine Starting