Cab Tilting
In order to permit easy access to the mechanical components and the hydraulic components, the cab can be tilted forward.
The hydraulic pump is operated manually. The hydraulic pump is used in order to raise the cab. The hydraulic pump is used in order to lower the cab.
- Remove bolts (1) and remove cover plate (2). The cover plates and the bolts are located on both sides of the cab. The cover plates and the bolts are located behind the seat.
Show/hide table
Illustration 2 g00348603 - Remove bolt (3) on each side of the machine. Remove nut (4) on each side of the machine.
Show/hide table
Illustration 3 g00348604 - Remove bolts (7) and remove spacers (8).
- Remove bolts (9) and (10).
- Install bolts (7) and spacers (8) into hole (6). Install spacers (8) between the cab and the frame pivot.
Show/hide table
Illustration 4 g00348605 - Remove cover (11) from the hydraulic pump. The pump is located on the right side of the machine.
Show/hide table
Illustration 5 g00348606 - Remove pump handle (12) from the storage location inside the cab.
Show/hide table
Illustration 6 g00348607 - Move valve (13) to the TOP position.
- Insert pump handle (12) into the pump. Move the handle upward and move the handle downward in order to raise the cab.
- Continue to raise the cab. After the cab is raised, install bolts (10) into the original bolt holes when bolt holes (6) are in alignment.
- Move valve (13) to the HORIZONTAL (NEUTRAL) position. The HORIZONTAL (NEUTRAL) position will prevent the buildup of pressure in the hydraulic system.
Show/hide table
Illustration 1 | g00348602 |
Use the photographs and callouts in Operation and Maintenance Manual, "Cab Tilting"for reference.
- Remove bolts (10).
Show/hide table
Illustration 8 g00348607 - Move valve (13) to the BOTTOM position.
Show/hide table
Illustration 9 g00348606 - In order to lower the cab, use pump handle (12).
- After the cab is lowered, install bolts (9) and (10).
- Remove bolts (7) and spacers (8) from hole (5).
- Install bolts (9) and spacers (6).
Show/hide table
Illustration 10 g00348603 - Install bolts (3) and nuts (4) that are located inside the cab. The bolts and nuts are located behind the seat.
Show/hide table
Illustration 11 g00348602 - Install cover plate (2) and bolts (1) that are located on each side of the cab. The cover plate and the bolts are located behind the seat.
Show/hide table
Illustration 12 g00348605 - Install cover (11) on the hydraulic pump.
Show/hide table
Illustration 7 | g00348604 |
Caterpillar Information System:
CP-563C and CS-563C Vibratory Compactors Lifting and Tying Down the Machine
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader E190 Engine Overspeed Warning
TL5 Series Field Cultivator Safety Signs and Labels
CP-563C and CS-563C Vibratory Compactors Engine and Machine Warm-Up
CP-563C and CS-563C Vibratory Compactors Engine Starting with Jump Start Cables
SR4 Generator with VR3 or VR4 Voltage Regulator Troubleshooting
SR4 Generator with VR3 or VR4 Voltage Regulator Service Tools
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0346 - FMI 03
SR4 Generator with VR3 or VR4 Voltage Regulator General Information
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinder
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
966G Series II and 972G Series II Wheel Loaders Engine Supplement Crankshaft Front Seal - Remove - Engine in Chassis
SR4 Generator with VR3 or VR4 Voltage Regulator Rotating Rectifier - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
Disassembly and Assembly of the Water Pump on the 3524B Engine{1361} Disassembly and Assembly of the Water Pump on the 3524B Engine{1361}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0346 - FMI 05
2001/10/15 Proper Adjustment of the Kickout Positioner Improves Reliability {5109, 5112}
2001/11/19 New Protective Caps For Hose Clamps Are Now Available {5057}
3408E and 3412E Engines for Caterpillar Built Machines Camshaft - Remove
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Pressure Switch (Retarder)
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Gear Pump (Hoist) - Remove
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System Pressure Switch (Automatic Retarder)