MID 027 - CID 0378 - FMI 05
产生此代码的情况:
Show/hide table
图 1 | g00803667 |
(自动润滑)电磁阀原理图 |
在 ECM 检测到电磁阀的电流低于正常值时会记录此诊断代码。
原因可能如下:
- 信号电路中存在断路。
- 电磁阀有故障。
- ECM 有故障。 但这种可能性很小。
注: 以下步骤会导致若干相关诊断代码产生。 在重新连接所有线束后,相关诊断代码不再显示为当前状态。 完成本程序后,清除所有相关诊断代码。
注: 确保电磁阀的诊断代码 CID 0378 FMI 05 处于当前状态。
系统响应:
由于电磁阀始终未打开,所以自动润滑不会打开。
测试步骤 1. 检查电磁阀。
- 将断路开关和钥匙起动开关转到 ON 位置。 不要起动发动机。
- 从电磁阀上断开机器线束。
- 在电磁阀的机器线束连接器上,将一根跨接导线连接在接触件 1(导线 E790-PK)与接触件 2(导线 801-PK)之间。
- 观测该诊断代码的状态。
预期结果:
该诊断代码处于当前状态。 安装然后拆下跨接导线后,该诊断代码不再处于当前状态。
结果:
- 是 - 电路正常。 电磁阀有故障。
修复: 重复进行"检查电磁阀"测试,确认电磁阀确已出故障。 更换电磁阀。
停止
- 否 - 该诊断代码仍为当前状态。 继续执行测试步骤2。
测试步骤 2. 检查电磁阀电路是否断路。
- 将钥匙起动开关和断路开关转到 OFF 位置。
- 从 ECM 上断开机器线束连接器 J2。
- 跨接导线仍然安装在电磁阀的机器线束连接器上。
- 在机器线束连接器 J2 上,测量接触件 J2-8(导线 801-PK)与 J2-3(导线 E790-PK)之间的电阻。
预期结果:
电阻应小于 5 欧姆。
结果:
- 是 - 电阻小于 5 欧姆。 机器线束正常。 继续执行测试步骤3。
- 否 - 测得的电阻不正常。 机器线束中存在断路。
修复: 电磁阀信号线或机器线束导线(E790-PK)中存在断路。 修理或更换机器线束。
停止
测试步骤 3. 检查该诊断代码是否仍然存在。
- 检查并清洁线束连接器的接触件。
- 重新连接所有线束连接器。
- 将断路开关和钥匙起动开关转到 ON 位置。
- 清除所有非当前状态的诊断代码。
- 运转机器。
- 停机并将停车制动器开关置于 ON 位置。
- 检查电磁阀的诊断代码是否处于当前状态。
预期结果:
该诊断代码不再为当前状态。
结果:
- 是 - 该诊断代码不再为当前状态。 该诊断代码此时不存在。 原有诊断代码可能是由于某个断开后又重新连接的线束连接器存在电气连接不良或短路而引起的。 使机器恢复正常工作。停止
- 否 - 该诊断代码尚未被排除。
修复: ECM 出故障的可能性非常小。 退出并重新执行本测试步骤。 确认该诊断代码仍处于当前状态。 如果没有找到导致该诊断代码的原因,则更换 ECM。 请参阅测试和调整, "电子控制模块(ECM)- 更换"。
停止
Caterpillar Information System:
216B, 226B, 232B, 236B, 242B, 246B, 248B, 252B, 262B and 268B Skid Steer Loaders Roading the Machine
561M Pipelayer Hook Winch - Install
735 Articulated Truck Power Train Pump Drive - Disassemble - The No. 1 Rotating Clutch is included.
2001/06/11 Repositioning the Hoses for the Ejector Bucket will Improve the Service Life of the Hoses {5057}
320C and 322C Forest Machines Hydraulic System Main Hydraulic System
2001/06/11 Revision to Systems Operation, Testing and Adjusting"Transmission Neutralizer Pressure Test" {3191, 4269}
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 0378 - FMI 03
2001/06/11 Revision to Specification , "Neutralizer Switch Assembly Adjustment" {3191, 4269}
2001/07/02 Procedure For the Pipelayer Boom Kickout Adjustment {6301}
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 1326 - FMI 02
CP-663E, CS-663E and CS-683E Vibratory Compactors Machine Systems Wheel and Tire - Remove and Install
CP-663E, CS-663E and CS-683E Vibratory Compactors Machine Systems Piston Motor (Axle Propel) - Assemble
2001/06/11 Correction to Disassembly and Assembly, SENR1206-01 , "Assemble Differential (Rear)" {3258, 3259, 3260, 3278}
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 0378 - FMI 06
2003/06/30 New Backup Rings Are Available for Sealing Hydraulic Cylinders with Pitted Grooves {4303, 5102, 5104, 5106, 5456, 7562}
2001/07/23 Wear Limits for the Mounts for the Rear Suspension {7203, 7207}
561M Pipelayer Hook Winch Motor - Remove
561M Pipelayer Hook Winch Motor - Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Hydraulic System Feed Roller Motor Speed - Test and Adjust
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Hydraulic System Feed Roller Motor Back Pressure - Test and Adjust
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Diagnostic Code List
2001/06/25 Correction to the Testing and Adjusting Procedure for the Pilot Accumulator {5077}
2001/06/18 Correction to Operation and Maintenance Manual, SEBU7468-01 for the Automatic Level Control Switch {1435}