Fan Guard - Remove and Install
Removal Procedure
- Remove three cable straps (1) in order to release hose (2) .
Show/hide table
 | |
| Illustration 1 | g00712143 |
- Remove three bolts (3), six washers and three nuts. Remove two nuts (4), the washers and bracket (5) .
Show/hide table
 | |
| Illustration 2 | g00712167 |
- Remove six bolts (6), the washers and fan guard (7) .
Show/hide table
 | |
| Illustration 3 | g00712180 |
Installation Procedure
- Install fan guard (7), six bolts (6), and the washers.
Show/hide table
| | |
| Illustration 4 | g00712180 |
- Install bracket (5), two nuts (4), and the washers. Install three bolts (3), six washers and the three nuts. Position bracket (5) in order to allow a 20 mm (0.75 inch) clearance between the fan and the radiator.
Show/hide table
| | |
| Illustration 5 | g00712167 |
- Install three cable straps (1) in order to secure hose (2) .
Show/hide table
| | |
| Illustration 6 | g00712143 |
Caterpillar Information System:
2000/06/05 A New Harness Is Available for Brooms {1408}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Muffler - Remove and Install
TH62, TH63, TH82 and TH83 Telehandlers Service Brake - Adjust
TH103 Telehandler Stabilizer and Cylinder Bearings - Lubricate
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Install
2000/05/22 A New Speed Sensor has Improved Service Life {3141, 3175}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>4P-2236</B> Generator through <B>4P-9907</B> Generator
120H and 135H Motor Graders Parking
143H and 163H Motor Graders Operation
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Differential - Disassemble
2000/06/05 New Lock Valves for the Stabilizers Keep the Cylinder Head Tight {5057, 5067, 5468}
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil - Change
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Remove
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 04 Engine Oil Pressure short to ground
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 0100 FMI 13 Engine Oil Pressure calibration required
2000/06/12 Improved Routing of the Wire for the Suspension Seat {7324}
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil Level - Check
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Assemble
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 04 Intake Manifold Air Temp short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Disassemble
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}