CID 0100 FMI 13 Engine Oil Pressure calibration required
Conditions Which Generate This Code:
The ECM detects one of the following conditions:
- The ECM reads engine oil pressure that is less than 35 kPa (5 psi).
- The ECM reads engine oil pressure that is greater than 130 kPa (19 psi).
- The engine oil pressure changes more than 25 kPa (3.6 psi) during a calibration attempt.
- The signal for the engine oil pressure has a difference of more than 27 kPa (4 psi) from the atmospheric pressure sensor signal when the key is ON and the engine is not running.
System Response:
The ECM will log the diagnostic code. The diagnostic code may be viewed on a display module or on ET. The engine monitoring system is disabled for crankcase pressure.
Further troubleshooting is required.
Test Step 1. Perform the following test: Engine Pressure Sensor - Calibrate
Results:
- OK - Stop.
Caterpillar Information System:
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 04 Engine Oil Pressure short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Remove
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil - Change
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Fan Guard - Remove and Install
2000/06/05 A New Harness Is Available for Brooms {1408}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Muffler - Remove and Install
TH62, TH63, TH82 and TH83 Telehandlers Service Brake - Adjust
TH103 Telehandler Stabilizer and Cylinder Bearings - Lubricate
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Install
2000/05/22 A New Speed Sensor has Improved Service Life {3141, 3175}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>4P-2236</B> Generator through <B>4P-9907</B> Generator
2000/06/12 Improved Routing of the Wire for the Suspension Seat {7324}
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil Level - Check
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Assemble
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 04 Intake Manifold Air Temp short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Disassemble
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 03 Fuel Temperature open/short to +batt
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Install
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt