Improved Routing of the Wire for the Suspension Seat {7324}
- Skid Steer Loader:
- 216 (PIN: 4NZ161, 162, 164-166, 169-191, 194-197, 199-263, 265-271, 274-282, 284-288, 290, 294, 316, 330 and 339)
- 226 (PIN: 5FZ264-266, 268-271, 273-276, 278-285, 288-290, 294-416, 418-438, 443-464, 466, 468, 473, 476, 477-481, 497, 498, 500, 502, 503, 513, 541-544, 578, 616, 618 and 619)
The seat switch may become disconnected when the suspension seat is moved fully forward. If the wire for the seat switch is under tension, the wire can be pulled off of the switch terminals.
The following indications are evidence that the seat switch has been disconnected:
- When the machine is OFF, the machine will not start and the indicator lamp for the seat belt will flash.
- When the machine is running, the indicator lamp for the seat belt will flash and the indicator lamp for the parking brake will light. The parking brake will not release.
Show/hide table
 | |
| Illustration 1 | g00712132 |
The 142-9304 Suspension Seat (1) 154-3986 Switch (2) 154-3985 Wire | |
In order to prevent the seat switch from being disconnected, perform the following procedure:
- Locate the 154-3986 Switch (1) and the 154-3985 Wire (2) that are under the right front of the suspension seat. The switch and the wire are part of the 142-9304 Suspension Seat. See Illustration 1.
- Inspect the routing of the 154-3985 Wire (2) in order to ensure that the wire is not under tension when the suspension seat is fully forward.
- If wire (2) appears to be under tension, perform the following steps in order to secure the wire to the seat mounting rail:
- Mark wire (2) at 102 mm (4.0 inch) from the 154-3986 Switch (1) .
- Mark the seat mounting rail at 76 mm (3.0 inch) behind switch (2) .
- Position wire (2) in order to align the mark on wire (2) and the mark on the seat mounting rail. Install a wire tie-wrap (3) at this point.
Note: There should be 25 mm (1.0 inch) of slack in wire (2) between the wire tie-wrap (3) and switch (1) .
Show/hide table
 | |
| Illustration 2 | g00715024 |
(1) 154-3986 Switch (2) 154-3985 Wire (3) Tie-wrap | |
Caterpillar Information System:
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 0100 FMI 13 Engine Oil Pressure calibration required
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 04 Engine Oil Pressure short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Remove
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil - Change
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Fan Guard - Remove and Install
2000/06/05 A New Harness Is Available for Brooms {1408}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Muffler - Remove and Install
TH62, TH63, TH82 and TH83 Telehandlers Service Brake - Adjust
TH103 Telehandler Stabilizer and Cylinder Bearings - Lubricate
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Install
2000/05/22 A New Speed Sensor has Improved Service Life {3141, 3175}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil Level - Check
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Assemble
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 04 Intake Manifold Air Temp short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Disassemble
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 03 Fuel Temperature open/short to +batt
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Install
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}