Transfer Gear Oil Level - Check
To check the oil for the transfer gear, the machine needs to be parked on level ground.
- Remove the filler plug for the transfer gear.
- If necessary, add oil to the transfer gear. Refer to Operation and Maintenance Manual, "Lubricant Viscosities". Add oil until the oil reaches the bottom of the filler plug hole.
- After you clean the filler plug, install the filler plug back into the housing.
Show/hide table
| |
| Illustration 1 | g00712140 |
Caterpillar Information System:
2000/06/12 Improved Routing of the Wire for the Suspension Seat {7324}
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 0100 FMI 13 Engine Oil Pressure calibration required
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 04 Engine Oil Pressure short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Remove
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil - Change
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Fan Guard - Remove and Install
2000/06/05 A New Harness Is Available for Brooms {1408}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Muffler - Remove and Install
TH62, TH63, TH82 and TH83 Telehandlers Service Brake - Adjust
TH103 Telehandler Stabilizer and Cylinder Bearings - Lubricate
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Install
2000/05/22 A New Speed Sensor has Improved Service Life {3141, 3175}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Assemble
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 04 Intake Manifold Air Temp short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Disassemble
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 03 Fuel Temperature open/short to +batt
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Install
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground