Front Suspension (Cylinder) - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 148-0357 | 支杆提升总成 | 1 |
A | 3R-2299 | 螺栓 | 8 |
B | 138-7576 | 连杆支架 | 3 |
C | 194-7586 | 气动扳手总成 | 1 |
C | 194-7886 | 驱动延伸件 | 1 |
C | 2P-2334 | 套筒 | 1 |
D | 7S-5437 | 充氮总成 | 1 |
注: 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。 利用正要密封的润滑剂稍微润滑所有 O 形密封圈。 利用不起毛的抹布擦拭所有部件。
- 在移动前悬挂油缸前,先确认两个销 (14) 和开口销安装在了工具 (A) 上。
Show/hide table
图 3 g00701301 - 将工具 (B) 固定到前悬挂油缸 (9) 上和前轮 (12) 上。 将适当的吊索放置到工具 (B) 上。 将吊索固定到适当的举倾机构上。 将前悬挂油缸 (9) 和心轴 (10) 作为一个组件升起至垂直位置。
- 将两个销 (14)(未显示)和开口销从工具 (A) 上拆下。
Show/hide table
图 4 g00714268 - 将前悬挂油缸 (9) 和心轴 (10) 作为一个组件放置在工具 (A) 的底座上,如图所示。 安装八个螺栓 (13)。 将工具 (B) 从前悬挂油缸 (9) 和前轮 (12) 上拆下。
Show/hide table
图 5 g00700058 - 将键 (11) 安装到机架组件上。
Show/hide table
图 6 g00714270 - 使用工具 (A) 和适当的升降机将前悬挂油缸 (9) 和心轴 (10) 作为一个组件提升到适当的位置。 安装将前悬挂油缸 (9) 固定在机架组件上的 16 个螺栓 (8)、垫圈和全螺纹螺母。 使用工具 (C)(未显示)拧紧全螺纹螺母至扭矩为
1173 ± 47 N·m (865 ± 35 lb ft) 。Show/hide table图 7 g00700055 注: 如果移动发动机进行维修,则发动机和管组件必须在安装垫片 (5) 之前安装。 安装垫片 (5) 之前,必须在主机架下方使用两个千斤顶均匀地支撑机器各侧。
- 将垫片 (5) 放置在机架组件上。 安装四个螺栓 (6)、硬垫圈和垫圈。
- 连接软管组件 (7)。
Show/hide table
图 8 g00700054 - 将线束 (4) 连接到电气接头上。
Show/hide table
图 9 g00700050 - 如图所示,将适当的吊索绕转向臂 (3) 安置。 将吊索固定到适当的举倾机构上。 将转向臂 (3) 提升到心轴上的适当位置。 安装四个螺栓 (2) 和硬垫圈。
Show/hide table
图 10 g00700051 - 将软管组件 (1) 连接到前钳式行车制动器上。
- 使用工具 (D)(未显示)向前悬挂油缸充油。 请参阅悬挂油缸,系统操作、测试和调整, "悬挂油缸(前)-排气和充气"。
- 把空气从制动器系统中排除出去。 请参阅测试和调整, "制动系统空气 - 排除"。
Show/hide table
图 1 | g00714263 |
Show/hide table
图 2 | g00714266 |
注: 只有当悬挂油缸水平放置时才要求步骤 1 至 4。
结束:
- 安装前轮胎和轮辋。 请参阅拆解和组装, "轮胎和轮缘(前) - 拆卸和安装"。
Caterpillar Information System:
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
3034 Engine for Caterpillar Built Machines Camshaft - Remove
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Leveling Blade
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
Process for Removal and Installation of Screed Plates and Nose Bars{6640, 6643} Process for Removal and Installation of Screed Plates and Nose Bars{6640, 6643}
2000/05/08 Correction to Guideline for Reusable Parts and Salvage Operations , "Axle Housing and Final Drive Hub Salvage Procedure for 24H Motor Graders" {3260, 4050}
2000/05/15 The Flash File For The Challenger 85D Has Been Updated {7620}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Work Tool Positioner
120H and 135H Motor Graders Circle Drive Oil Level - Check
2000/04/17 Correction to Disassembly and Assembly Module For The Disassembly of The Transmission {3030}
2000/05/29 Use 178-3832 Tank Valve to Check Pressure Regulator Settings {5505, 5506}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
24H Motor Grader Plate Locations and Film Locations
2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble
3034 Engine for Caterpillar Built Machines Camshaft - Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3114, 3116, and 3126 Engines Fuel System - Prime