Air/Hydraulic Cylinder (Front Caliper) - Disassemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 1P-1856 | 挡圈钳 | 1 |
开始:
- 拆下空气/液压油缸(前钳式)。 请参阅拆解和组装, "空气/液压油缸(前钳式)- 拆卸"。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 将空气/液压油缸放置在软口台钳(未显示)中。 松开螺母 (1)。
- 从软口台钳上拆下空气/液压油缸。 从油缸组件 (2) 上拆下油缸管 (3)。
Show/hide table
图 2 g00487023 - 将油缸管 (3) 放置在软口台钳(未显示)上。 松开螺母 (6)。 从油缸管 (3) 上拆下端盖 (5)。 从油缸管 (3) 各端拆下 O 形密封圈 (7)。
- 从端盖 (5) 上拆下排气螺钉 (4)。
Show/hide table
图 3 g00487024 - 从油缸组件 (2) 上拆下八个锁紧螺母 (8)。
Show/hide table
图 4 g00487025 - 分离油缸组件 (2)。 从油缸组件 (2) 上拆下密封垫 (9)(未显示)。
Show/hide table
图 5 g00487026 - 从油缸组件 (2) 上拆下通风装置 (10)。
Show/hide table
图 6 g00487027 Show/hide table拆卸固定环和弹簧时,可能会造成伤害。
拆卸固定环时,将释放弹簧力。
拆卸固定环时,做好固定油缸组件的准备。
- 用手向下推动活塞 (12) 和连杆 (17),直到动力活塞 (22) 从活塞组件 (2) 上脱离。
- 使用工具 (A)(未显示)拆下挡圈 (19)。 从连杆 (17) 上拆下带阀 (20) 和阀镶圈 (21) 的动力活塞 (22)。
- 从动力活塞 (22) 中拉出阀 (20) 和阀镶圈 (21)。 从动力活塞 (22) 上拆下唇形密封 (23)。
- 从连杆 (17) 上拆下弹簧 (16)。
- 从连杆 (17) 上拆下锁紧螺母 (11) 和活塞 (12)。
- 拆下活塞外圈 (13) 和活塞外圈弹簧。
- 从活塞 (12) 上拆下 O 形密封圈 (15) 和活塞密封件 (14)。
- 从油缸组件 (2) 上拆下两个方形密封件 (18)。
Show/hide table
图 1 | g00487022 |
Caterpillar Information System:
2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}
24H Motor Grader Plate Locations and Film Locations
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
3034 Engine for Caterpillar Built Machines Camshaft - Remove
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Leveling Blade
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble
3034 Engine for Caterpillar Built Machines Camshaft - Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3114, 3116, and 3126 Engines Fuel System - Prime
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Front) - Remove and Install
Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}
24H Motor Grader Battery Disconnect Switch
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Rear) - Remove and Install
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate
797 Off-Highway Truck Power Train Relief Valve (Rear Axle Motor Unloader) - Disassemble