Camshaft - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Slide camshaft assembly (1) into the cylinder block.
Show/hide table
 | |
| Illustration 1 | g00701151 |
- Align the timing marks on idler gear (2) and on the camshaft gear (3) .
Show/hide table
 | |
| Illustration 2 | g00701149 |
- Install bolts (4) that secure the camshaft assembly to the cylinder block.
- Tighten bolts (4) to 9 N·m (80 lb in).
End By:
- Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
- Install the rocker shaft assembly and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrods - Install ".
Caterpillar Information System:
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble
2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}
24H Motor Grader Plate Locations and Film Locations
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
3034 Engine for Caterpillar Built Machines Camshaft - Remove
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3114, 3116, and 3126 Engines Fuel System - Prime
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Front) - Remove and Install
Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}
24H Motor Grader Battery Disconnect Switch
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Rear) - Remove and Install
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate
797 Off-Highway Truck Power Train Relief Valve (Rear Axle Motor Unloader) - Disassemble
2000/04/17 The Torque For The Nuts On The Injector Wiring Harness Has Been Increased {1290}
24H Motor Grader Engine Start Switch