Rework for Certain Rear Lamp Housing Groups {1429}
- Off-Highway Truck/Tractor:
- 777D (PIN: AGC1-UP)
- 776D (PIN: AFS1-UP)
- 777D (PIN: AYS1-UP)
The rear light wiring does not fit around the 135-3448 Housing. The housing is a part of the 161-4016 Rear Lamp Group. Rework the 135-3448 Housing. The following rework provides the proper routing for the rear light wiring.
Show/hide table
Illustration 1 | g00701172 |
This is a view (A) of the area that is modified on the housing. |
Show/hide table
Illustration 2 | g00701545 |
Show/hide table
Illustration 3 | g00701185 |
This is a view (A) that shows the areas that are cut on the housing. (A) 12 mm (0.47 inch) (B) 12 mm (0.47 inch) |
Cut out a 12 mm (0.47 inch) by 12 mm (0.47 inch) section from the housing. Use a suitable cutting device. Refer to the illustrations above.
Caterpillar Information System:
24H Motor Grader Plate Locations and Film Locations
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
3034 Engine for Caterpillar Built Machines Camshaft - Remove
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Leveling Blade
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble
3034 Engine for Caterpillar Built Machines Camshaft - Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3114, 3116, and 3126 Engines Fuel System - Prime
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Front) - Remove and Install
Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}
24H Motor Grader Battery Disconnect Switch
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Rear) - Remove and Install
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate