Circle Drive Oil Level - Check
如果出现漏油，或怀疑漏油，对油位进行检查。
检查油位和加注机油之前，先把检查/加注螺塞口周围面上抹干净。
Show/hide table
 | |
| 图 1 | g00700760 |
Show/hide table
 | |
| 图 2 | g00108110 |
- 拆下检查/加注塞。
- 油位要保持在检查/加注螺塞口底部。
- 安装检查/加注孔螺塞。
Caterpillar Information System:
2000/04/17 Correction to Disassembly and Assembly Module For The Disassembly of The Transmission {3030}
2000/05/29 Use 178-3832 Tank Valve to Check Pressure Regulator Settings {5505, 5506}
3126B Engine for Lexion 450, Lexion 460, and Lexion 460 R Combines Diagnostic Enable Switch Circuit - Test
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>115-5101</B> Generator through <B>121-6860</B> Generator
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0359 - FMI 06
3114, 3116, and 3126 Engines Fuel Ratio Control - Adjust
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Steering Motor - Assemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Steering Motor - Disassemble
24H Motor Grader Power Train Torque Converter Lockup Clutch Pressure - Test
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0359 - FMI 03
D350E Series II and D400E Series II Articulated Trucks Differential Lock Control
2000/08/14 The Swashplate Stop for the Piston Pump is now Retained with a Dowel Pin {5070}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Work Tool Positioner
2000/05/15 The Flash File For The Challenger 85D Has Been Updated {7620}
2000/05/08 Correction to Guideline for Reusable Parts and Salvage Operations , "Axle Housing and Final Drive Hub Salvage Procedure for 24H Motor Graders" {3260, 4050}
Process for Removal and Installation of Screed Plates and Nose Bars{6640, 6643} Process for Removal and Installation of Screed Plates and Nose Bars{6640, 6643}
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Leveling Blade
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
3034 Engine for Caterpillar Built Machines Camshaft - Remove
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble