Transmission from Torque Converter - Separate
Separation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 4 |
Start By:
- Separate the output transfer gears from the transmission planetary group. Refer to Disassembly and Assembly, "Output Transfer Gears from Tranmission, Torque Converter - Separate" for the machine that is being serviced.
Note: Cleanliness is an important factor. Before the separation procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Remove bolt (1) and the washers. Remove two hoses (2) .
Show/hide table
 | |
| Illustration 1 | g00509029 |
- Remove bolt (3), the clamps, the nut and the washers.
- Remove four bolts (4) and the washers. Remove hose assembly (6) from tube assembly (5) .
- Remove five bolts (7) and the washers from manifold (8) .
Show/hide table
 | |
| Illustration 2 | g00509030 |
- Remove manifold (8) .
- Install Tooling (A) to transmission (9). Attach a hoist and suitable lifting straps to Tooling (A) .
Show/hide table
 | |
| Illustration 3 | g00509031 |
- Remove eleven bolts (11) and the washers that secure transmission (9) to torque converter (10) .
Show/hide table
 | |
| Illustration 4 | g00509033 |
- Remove two brackets (12) .
- Use the hoist to carefully separate transmission (9) from torque converter (10). The weight of the transmission is 635 kg (1400 lb).
Show/hide table
 | |
| Illustration 5 | g00509034 |
- Remove output shaft (13) .
- Remove O-ring seal (14) from transmission (9) .
Show/hide table
 | |
| Illustration 6 | g00509036 |
Caterpillar Information System:
CB-534C and CB-634C Vibratory Compactors Vibratory System Pressure Valve (POR) - Test and Adjust
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Sloper Jack - Lubricate
12H, 140H and 160H Motor Graders Machine Systems Blade Lift Cylinder - Install
CB-534C Vibratory Compactor Cooling System Pressure Cap - Clean/Replace
CB-534C Vibratory Compactor Cooling System Coolant Level - Check
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Height Adjuster - Lubricate
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Drop Arm - Lubricate
2014/08/20 New Water Pump Group Includes Many Improvements {1361}
12H, 140H and 160H Motor Graders Machine Systems Blade Lift Cylinder - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel - Inspect
988G Wheel Loader Engine Supplement Turbocharger - Install - Engine In Chassis
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Oil in Exhaust System
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Logged Event Mode
980G Wheel Loader Power Train Transmission to Torque Converter - Connect
CB-534C Vibratory Compactor Cooling System Water Temperature Regulator - Replace
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Thickness Control - Lubricate
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Vibratory Shaft Bearing - Lubricate
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Gear Group (Front) - Time
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Switches
12H, 140H and 160H Motor Graders Machine Systems Sideshift Cylinder - Remove
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Vibratory Shaft and Universal Joint - Lubricate
3054 Engine Air in Fuel - Test
CB-535B Vibratory Compactor Propel System Speed and Direction Control
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel System Pressure - Test