Inverter Valve (Secondary Brake) - Remove
Removal Procedure
Start By:
- Purge the air pressure from the air tanks. Refer to Disassembly and Assembly, "Air Tanks (Brake) - Purge".
Show/hide table
Personal injury can result from removing hoses or fittings in a pressure system. Failure to relieve pressure can cause personal injury. Do not remove or disconnect hoses or fittings until all pressure in the air system has been relieved. |
Note: The inverter valve is located above the service brake air tank.
- Put identification on hose assemblies (2), (3), and (4) for installation purposes.
Show/hide table
Illustration 1 | g00505024 |
Note: Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will prevent dirt from entering the internal components.
- Disconnect hose assemblies (2), (3), and (4) from inverter valve (1) .
- Remove bolts (5) that secure inverter valve (1) to the plate assembly.
- Remove inverter valve (1) from the plate assembly.
Caterpillar Information System:
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Hoist Cylinder
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
583R Pipelayer Power Train Final Drive - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner - Remove
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Tank (Steering) - Assemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Tank (Steering) - Disassemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Fuel Tank - Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Fuel Tank - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Fuel Level Sensor - Remove and Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Control Valve (Hoist) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
773D Off-Highway Truck and 775D Quarry Truck Engine Starting with Ether Starting Aid - If Equipped
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 03 Sensor Power Supply (8 DCV) Voltage Above Normal - Test
572R Pipelayer Power Train Bevel and Transfer Gears - Assemble
824G , 825G and 826G Landfill Compactor Reversing Fan Control
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Position Sensor (Dump Body) - Adjust
824G , 825G and 826G Landfill Compactor Power Guard Control
583R Pipelayer Power Train Final Drive - Assemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Inverter Valve (Secondary Brake) - Install
3176C and 3196 Engines for Caterpillar Built Machines Fuel Transfer Pump
3408E and 3412E Engines for Caterpillar Built Machines Valve Rocker Arms, Lifters, and Bridges
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Hydraulic Operational Checks
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Retaining Ring and Pin (Body) - Remove and Install