Hydraulic Tank (Steering) - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     |
Part Description     | Qty     |
A     | 5P-9119     | Sealant     | 1     |
- Check all of the O-ring seals and the components for wear or damage. Replace the components, if necessary.
- Lubricate all of the O-ring seals lightly with the lubricant that is being sealed.
- Place Tooling (A) on the cover assembly for the hydraulic tank, as shown. Form a crisscross pattern over the top bolt hole of the cover assembly with the beginning and ending point of Tooling (A) .
Show/hide table
Illustration 1 | g00544406 |
- Position the cover assembly (10) on the steering hydraulic tank (1). Secure the cover assembly with bolts (9) and the locknuts.
Show/hide table
Illustration 2 | g00504605 |
- Install sight gauge (8), the bolts, and the O-ring seals. Tighten the bolts to a torque of 7 ± 1 N·m (62 ± 9 lb in). Install the O-ring seal and breaker relief valve (7) .
Show/hide table
Illustration 3 | g00504590 |
- Install elbow (6) and the O-ring seal to steering hydraulic tank (1).
Show/hide table
Illustration 4 | g00504589 |
- Install the plug adapter, the gasket, and two bolts (5) to steering hydraulic tank (1) .
- Install screen assembly (4) and the O-ring seal to steering hydraulic tank (1).
- Install the base, oil filter (3), locknuts (2), and the washers to steering hydraulic tank (1) .
Show/hide table
Illustration 5 | g00504588 |
End By: Install the hydraulic tank (steering). Refer to Disassembly and Assembly, "Hydraulic Tank (Steering) - Install".
Caterpillar Information System:
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Tank (Steering) - Disassemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Fuel Tank - Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Fuel Tank - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Fuel Level Sensor - Remove and Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Control Valve (Hoist) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Gear Pump (Hoist and Brake) - Install
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Relief Valve (Rear Brake Oil Cooler) - Test and Adjust
836G Landfill Compactor and 834G Wheel Dozer Safety Messages
572R Pipelayer Power Train Final Drive - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Detent Kickout Pressure Test
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner - Remove
583R Pipelayer Power Train Final Drive - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Hoist Cylinder
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Inverter Valve (Secondary Brake) - Remove
773D Off-Highway Truck and 775D Quarry Truck Engine Starting with Ether Starting Aid - If Equipped
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 03 Sensor Power Supply (8 DCV) Voltage Above Normal - Test
572R Pipelayer Power Train Bevel and Transfer Gears - Assemble
824G , 825G and 826G Landfill Compactor Reversing Fan Control
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Position Sensor (Dump Body) - Adjust
824G , 825G and 826G Landfill Compactor Power Guard Control
583R Pipelayer Power Train Final Drive - Assemble