Fuel Tank - Remove
开始:
- 安装车斗固定销。 请参阅拆解和组装, "挡圈和销钉(车斗)- 拆卸和安装"。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
注: 将盖和塞安装在全部孔口上,以免污垢或碎屑进入系统。 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这将防止脏污进入内部部件。
- 慢慢打开燃油箱盖组件,释放燃油箱中的压力。 从燃油箱 (1) 底部拆下管塞 (2)。 排出燃油箱 (1) 中的燃油。 采用适当的容器存放或处理。 燃油箱 (1) 的容量为
700 L (185 US gal) 。Show/hide table图 2 g00504560 - 在软管组件上标上识别标记,以用于安装目的。 从燃油箱 (1) 上断开软管组件 (3)。
Show/hide table
图 3 g00504562 - 断开线束组件 (4)。
Show/hide table
图 4 g00504563 - 拆下螺栓 (5) 和夹子 (6)。
Show/hide table
图 5 g00504564 - 将螺栓 (7)、垫圈、硬垫圈和锁紧螺母从燃油箱 (1) 的底部拆下。 检查两个支架 (8) 是否磨损或损坏。 如有必要,拆卸燃油箱 (1) 后更换支架。
Show/hide table
图 6 g00504565 - 将两根吊索连接至燃油箱 (1),如图所示。 将吊索固定到适当的举倾机构上。
Show/hide table
图 7 g00504570 - 将螺母 (9) 和 U 形螺栓 (10) 从燃油箱 (1) 左侧拆下。
Show/hide table
图 8 g00504574 - 将螺母 (11) 和 U 形螺栓 (12) 从燃油箱 (1) 右侧拆下。
- 稍稍提起燃油箱,以清洁机架组件。 小心地将燃油箱从机架组件上移开,直到球阀脱离机架组件。 燃油箱 (1) 的重量约为
297 kg (655 lb) 。
Show/hide table
图 1 | g00504555 |
Caterpillar Information System:
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Fuel Level Sensor - Remove and Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Control Valve (Hoist) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Gear Pump (Hoist and Brake) - Install
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Relief Valve (Rear Brake Oil Cooler) - Test and Adjust
836G Landfill Compactor and 834G Wheel Dozer Safety Messages
572R Pipelayer Power Train Final Drive - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Detent Kickout Pressure Test
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System System Schematic
793B Off-Highway Truck Air System and Brakes Towing the Machine - Preparation
789C Off-Highway Truck/Tractor Air System and Brakes Relief Valve (Electric Drive Pump) - Adjust
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Fuel Tank - Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Tank (Steering) - Disassemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Tank (Steering) - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner - Remove
583R Pipelayer Power Train Final Drive - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Hoist Cylinder
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Inverter Valve (Secondary Brake) - Remove
773D Off-Highway Truck and 775D Quarry Truck Engine Starting with Ether Starting Aid - If Equipped
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 03 Sensor Power Supply (8 DCV) Voltage Above Normal - Test
572R Pipelayer Power Train Bevel and Transfer Gears - Assemble
824G , 825G and 826G Landfill Compactor Reversing Fan Control