Electrical Problems And Malfunctions
Usage:
WHEEL LOADERS938G (6WS565-1290),
IT38G (1CW327-341),
950G (5FW217-773, 2JS251-543),
962G (7BW210-378, 3BS217-384),
966FII (9YJ4662-5265),
970F (9JK821-879),
980G (9CM985-1138) WHEEL LOADERS
IT38G (1CW327-341),
950G (5FW217-773, 2JS251-543),
962G (7BW210-378, 3BS217-384),
966FII (9YJ4662-5265),
970F (9JK821-879),
980G (9CM985-1138) WHEEL LOADERS
Problem:
Electrical problems have been reported on above listed machine S/N ranges. Sometimes Service Code 248-F02 (Cat Data Link) is shown up on CMS display. It can happen machines are stopped and it is not possible to start them again.
Solution:
The root cause of the problem can be in loose connections in the electrical box located in the engine compartment. In case of electrical problem, open the electrical box and verify that all wire connections are correctly tightened on switches, relays, breakers, ...
Show/hide table
 |
Before to intervene in the electrical box, the main circuit switch must be turned OFF to avoid short circuits. |
 |
CATERPILLAR BELGIUM MEDIUM WHEEL LOADERS COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar Information System:
Rear Axle Trunnion Bolted Joints Rear Axle Trunnion Bolted Joints
Intermittent "Soft Brake Pedal" Intermittent "Soft Brake Pedal"
Certain Pavers May Pull Or Drift Towards One Side Certain Pavers May Pull Or Drift Towards One Side
Bearing Part Number Listed Incorrectly For Transmissions Bearing Part Number Listed Incorrectly For Transmissions
Kickout Positioner Adjustment Kickout Positioner Adjustment
785 Steering Pump (4T-0382) Installation/Start-Up 785 Steering Pump (4T-0382) Installation/Start-Up
Transmission Control Software Correction For Shift Lever Diagnostic Code Flashing Transmission Control Software Correction For Shift Lever Diagnostic Code Flashing
Machining Premachined Valve Seat Inserts Machining Premachined Valve Seat Inserts
Correct Packaging Of Transmission Rotating Seals Correct Packaging Of Transmission Rotating Seals
Charge Filter Indicator Leaks Charge Filter Indicator Leaks
For Calibration Of Transmission Clutch Engagement - Use Only 4C-8195 Control Service Tool For Calibration Of Transmission Clutch Engagement - Use Only 4C-8195 Control Service Tool
3300 Engine Oil Level Maintenance And High Oil Consumption 3300 Engine Oil Level Maintenance And High Oil Consumption
THE HEAD OF THE STICK CYLINDER MAY LOOSEN THE HEAD OF THE STICK CYLINDER MAY LOOSEN
Brake And Inching Pedal Control Linkage Brake And Inching Pedal Control Linkage
Alternator Drive Belt Retention Alternator Drive Belt Retention
Correct Service Replacement Part Numbers For 100-5778 Caterpillar Monitoring System Control Correct Service Replacement Part Numbers For 100-5778 Caterpillar Monitoring System Control
New Drum Edge Profile May Minimize Mat Marking With Fine "Mixes" New Drum Edge Profile May Minimize Mat Marking With Fine "Mixes"
Leave Bolts Installed If Removing Front Counterweight Bracket Leave Bolts Installed If Removing Front Counterweight Bracket
Backhoe Loader Steering Cylinder May Malfunction Backhoe Loader Steering Cylinder May Malfunction
Missing Rear Gear Train Idler Shaft Mounting Bolt Seals May Result In Oil Leaks Missing Rear Gear Train Idler Shaft Mounting Bolt Seals May Result In Oil Leaks
Erratic Engine Oil Pressure Readings Erratic Engine Oil Pressure Readings
Tire Shortages For Backhoe Loaders Tire Shortages For Backhoe Loaders
Improperly Torqued Driveshaft Yoke Hardware Improperly Torqued Driveshaft Yoke Hardware
Roller Retainer Bolt Loosening Roller Retainer Bolt Loosening