1983/10/17 Caterpillar


Broken Edge Filter Or Plugged Cylinder Head Adapter Can Cause Rough Engine Operation Or Low Power{1252}

Usage:


All 3204 And 3208 Engines

A broken edge filter or a plugged cylinder head adapter can cause rough engine operation or low power. Under some conditions, it was possible for the edge filter to crack or break.

If a section of the edge filter breaks off, and it is larger than the orifice in the cylinder head adapter, there can be two results. First, the broken section can cause a complete restriction (plug) in the orifice of the cylinder head adapter as shown in Illustration 1. If the restriction is at the other end of the fuel passage, it can not be seen. To check for this condition, blow air through the inlet end of the adapter. See Illustration 2. A restriction in the air flow will be the result if there is a restriction in the fuel passage.


Illustration 1. Nozzle on the right has a restriction caused by a broken edge filter.


Illustration 2. Blow air through inlet to check for an internal restriction.

A second result when a section of the edge filter breaks off is shown in Illustrations 3 and 4. The broken section of the filter is continually forced against the walls inside the adapter by the high pressure fuel. Each time the broken section of the filter makes contact with the adapter walls, small pieces break off and pass through the adapter and into the fuel nozzle. Illustration 3 shows what is left from a piece of the edge filter after it has been broken down by the high pressure fuel.

As the small pieces pass through the cylinder head adapter and the fuel lines for the fuel nozzles, the ferrules on the nozzles are damaged. Illustration 4 shows the effect of these small pieces on the ferrule surface.

New edge filters are used in the cylinder head adapters on 3204 and 3208 Engines. The new edge filters are stronger than the former edge filters. The part number of the cylinder head adapters has not changed. See Illustration 5 for identification of the cylinder head adapters with the new edge filters.


Illustration 3. Example of a broken edge filter.


Illustration 4. Fuel nozzle ferrule damaged by a broken edge filter.


Illustration 5. New and former edge filters.

Caterpillar Information System:

1983/10/10 Cab Head Lamps Mounted In New Location For Better Protection{7309}
1983/10/10 New Water Pump Oil Seal Prevents Leaks{1361}
1983/10/10 New Service Centers For 6V3100 Engine Timing Indicator Group{0651}
1983/10/10 New Connecting Rod And Main Bearings Used{1203,1219,1226,1227,1230}
1983/10/10 S.O.S Program Synopsis{1318,5068,3179,0652}
1983/10/03 Use 6V6070 Tool Group And New Adjustment Procedure For New Scroll Fuel System{0654,1264,1278}
1983/09/26 New Seals Used In Tandem Drive Group{4064,4062,4071}
1983/09/26 Clearance Between Boom And Upper Frame{6501}
1983/09/26 New Drawbar And Yoke Assemblies Have Stronger Cross Bar To Prevent Damage{6153}
1983/09/26 Product Identification Number To Replace Serial Number On Earthmoving Equipment{7557}
1983/09/26 New Cover Assemblies For Transmission Hydraulic Controls Permit Better Access to Pressure Fittings{3150}
1983/09/26 Service Information For Woodward Governors{0374,1264}
1983/10/17 Fan Drive Conversion Group Available To Change Fans From Gear Driven To Belt Driven{1359,1356}
1983/10/17 Installation Of Vent Assembly Helps Prevent Oil Leakage In The Wheel Leaning Mechanism{5224}
1983/10/17 New Rod And Seal Used To Prevent Oil Leakage Into The Transmission Neutralizer Group{3181}
1983/10/17 Instrument Panel Changed To Give Better Fit For Gauges{7451}
1983/10/17 Modification Of Control Panel Gives Different Power Source For Overcrank Timer To Prevent Starter Motor Failures{7450}
1983/10/17 Stronger Spider Assemblies Used In Fan Groups{1356}
1983/10/17 Changes To Torque Converter Inlet Relief Valve Increase Service Life{3167}
1983/10/17 If The Cab Door Is Difficult To Open, Check Nylon Washer For Damage{7308}
1983/10/17 Use Shims At Both Ends Of Housing Assembly To Prevent Oil Leakage From Power Control Group{5201}
1983/10/17 New Rod Ends And Supports Used In Hydraulic Control Groups{5452}
1983/10/17 New Pump Drive Gear And Shaft Have More Clearance{3101,3108}
1983/10/17 Remanufactured Fuel Pump And Governor Groups{1251,1264}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.