140 Motor Grader Caterpillar

Transmission and Differential Oil Sample - Obtain

Usage:

140 N94

Show/hide table

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

Show/hide table

NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat^® products. Dispose of all fluids according to local regulations and mandates.

Show/hide table




Illustration 1	g06348403

Sampling valve (1) for the transmission and differential oil is on the transmission filter. The transmission filter is on the right, rear of the transmission.

Refer to Special Publication, SEBU6250, "S·O·S Services Oil Analysis" for information that pertains to obtaining a sample of the transmission and differential oil. Refer to Special Publication, PEHP6001, "How To Take A Good Oil Sample" for more information about obtaining a sample of the transmission and differential oil.

Caterpillar Information System:

140 Motor Grader Transmission and Differential Oil Level - Check

140 Motor Grader Transmission and Differential Oil Filter and Screens - Replace/Clean

140 Motor Grader Transmission and Differential Oil - Change

140 Motor Grader Tandem Drive Oil Sample - Obtain

140 Motor Grader Tandem Drive Oil Level - Check

140 Motor Grader Tandem Drive Oil - Change

140 Motor Grader Tandem Breather - Clean/Replace

Repair/Replacement Procedure for 5C-6108 Refueling Switch {1295} Repair/Replacement Procedure for 5C-6108 Refueling Switch {1295}

140 Motor Grader Steering Cylinder Ends and Tie Rods - Lubricate

140 Motor Grader Rollover Protective Structure (ROPS) - Inspect

140 Motor Grader Oil Filter (All Wheel Drive) - Replace - If Equipped

140 Motor Grader Moldboard Wear Strip - Inspect/Adjust/Replace

C9.3B Engines for Caterpillar Built Machines Nitrogen Oxide Sensor (Exhaust Outlet) - Remove and Install

C32 Marine Engines Auxiliary Water Pump - Remove

320 GC, 320 and 323 Excavator Production Measurement Application

336, 336 GC and 340 Excavator Systems Cylinder Drift - Check - Empty Bucket

Cat® PVT110, PVT115, PVT117, PVT120 Photo Voltaic Module {1471, 4822} Cat® PVT110, PVT115, PVT117, PVT120 Photo Voltaic Module {1471, 4822}

New Aftercooler Heat Shield Assemblies is Now Used for Certain 3500 Marine Engines {1063, 1073} New Aftercooler Heat Shield Assemblies is Now Used for Certain 3500 Marine Engines {1063, 1073}

Rework Procedure of the Coolant Level Wiring Harness on Certain G3306B Generator Sets {1408, 4459, 7422, 7938} Rework Procedure of the Coolant Level Wiring Harness on Certain G3306B Generator Sets {1408, 4459, 7422, 7938}

140 Motor Grader Operator Controls

336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Battery - Remove and Install

C9.3B Engines for Caterpillar Built Machines Temperature Sensor (Catalyst Inlet) - Remove and Install

140 Motor Grader Monitoring System

New Turbochargers and Cartridges Are Now Used for Certain 3500 Marine Engines {1052, 1056} New Turbochargers and Cartridges Are Now Used for Certain 3500 Marine Engines {1052, 1056}