Tandem Drive Oil - Change
Show/hide table
 |
|
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| |
| Illustration 1 | g06250028 |
- Clean the surface area around oil check plug (1).
- Remove drain plug (2). Remove the oil check plug. Allow the oil to drain into a suitable container.
Note: When you change the tandem drive oil, use diesel fuel to clean the housing of the sludge and flush the housing of the sludge.
- Clean the drain plug and install the drain plug.
- Remove a plate from the walkway that is on top of the tandem drive housing. This must be done to access one of the covers on the top of the tandem drive housing.
- Clean the area around one of the covers of any dirt or debris. This must be done before the cover is removed.
- Remove a cover from the top of the tandem drive housing. Fill the tandem drive housing with new oil. Refer to the following topics:
- Operation and Maintenance Manual, "Lubricant Viscosities"
- Operation and Maintenance Manual, "Capacities (Refill)"
- Clean the cover and install the cover on the top of the tandem drive housing.
- Install the plate to the walkway.
- Clean the oil check plug and install the oil check plug.
- Start the engine. Operate the machine for a few minutes. Check the tandem drive housing for leaks.
- Stop the engine. Remove the oil check plug.
- Check the oil level. Maintain the oil level to the bottom of the opening for the oil check plug. Add oil, if necessary.
- Install the oil check plug.
- Repeat Step 1 through Step 13 for the other side of the machine.
Caterpillar Information System:
140 Motor Grader Tandem Breather - Clean/Replace
Repair/Replacement Procedure for 5C-6108 Refueling Switch {1295} Repair/Replacement Procedure for 5C-6108 Refueling Switch {1295}
140 Motor Grader Steering Cylinder Ends and Tie Rods - Lubricate
140 Motor Grader Rollover Protective Structure (ROPS) - Inspect
140 Motor Grader Oil Filter (All Wheel Drive) - Replace - If Equipped
140 Motor Grader Moldboard Wear Strip - Inspect/Adjust/Replace
140 Motor Grader Hydraulic System Oil - Change
140 Motor Grader Fuses - Replace
C9.3B Engines for Caterpillar Built Machines Nitrogen Oxide Sensor (Exhaust Inlet) - Remove and Install
140 Motor Grader Secondary Steering - Test
330, 330 GC, 336, 336 GC and 340 Excavator Tool Control Medium Pressure: Relief Valve (Main) - Test and Adjust
320GC and 320 Excavator Engine Supplement Water Temperature Regulator - Remove and Install
140 Motor Grader Tandem Drive Oil Level - Check
140 Motor Grader Tandem Drive Oil Sample - Obtain
140 Motor Grader Transmission and Differential Oil - Change
140 Motor Grader Transmission and Differential Oil Filter and Screens - Replace/Clean
140 Motor Grader Transmission and Differential Oil Level - Check
140 Motor Grader Transmission and Differential Oil Sample - Obtain
C9.3B Engines for Caterpillar Built Machines Nitrogen Oxide Sensor (Exhaust Outlet) - Remove and Install
C32 Marine Engines Auxiliary Water Pump - Remove
320 GC, 320 and 323 Excavator Production Measurement Application
336, 336 GC and 340 Excavator Systems Cylinder Drift - Check - Empty Bucket
Cat® PVT110, PVT115, PVT117, PVT120 Photo Voltaic Module {1471, 4822} Cat® PVT110, PVT115, PVT117, PVT120 Photo Voltaic Module {1471, 4822}
New Aftercooler Heat Shield Assemblies is Now Used for Certain 3500 Marine Engines {1063, 1073} New Aftercooler Heat Shield Assemblies is Now Used for Certain 3500 Marine Engines {1063, 1073}