Track Carrier Roller - Remove and Install
参考: 专门说明书, "目视维修步骤 - 颜色和符号" , M0066576。
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 439-5575 | 液压千斤顶 | 1 |
- 起动发动机。 把机器停放在坚硬的水平地面上。 关闭发动机。
Show/hide table
 |
|
油脂和机油从安全阀中溢出可能导致人身伤亡。 处于高压下的油脂和机油从安全阀中溢出，可能渗透阀体。 不要通过安全阀来观察油脂是否溢出。 应通过履带或履带调节油缸查看履带是否松脱。 确保通风孔清洁，然后释放履带上的张紧力。 |
Show/hide table
| |
| 图 1 | g06189409 |
Show/hide table
| |
| 图 2 | g06189410 |
安全阀只能拧松一圈。 如果履带在安全阀打开后没有放松，请前后移动机器，直到释放张紧度。
Show/hide table
| |
| 图 3 | g06189415 |
Show/hide table
| |
| 图 4 | g06189417 |
参考: 有关履带托链轮的拆解和组装步骤，请参阅底盘系统修复公报, SEBF8568, "液压挖掘机滚轮拆解和组装过程"。
确保履带托链轮的轴和底盘系统上安装支架中的孔清洁并且没有灰尘。
Show/hide table
| |
| 图 5 | g06189422 |
调整托链轮直到距离 (X)（即安装支架外表面和和托链轮之间的距离）为
Show/hide table
| |
| 图 6 | g06189424 |
Show/hide table
| |
| 图 7 | g06189425 |
张紧履带的张力。 有关正确的步骤，请参阅操作和保养手册, "履带的调整 - 调整"。
Caterpillar Information System:
PM620 and PM622 Cold Planer Water Spray Pump Oil (High Pressure) - Change
320GC, 320 and 323 Excavators Machine Systems Track Roller - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Front Idler and Recoil Spring - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Counterbalance Valve (Travel) - Remove and Install
320 GC, 320 and 323 Excavator Machine Systems Machine System
120 and 120 AWD Motor Grader Restricted Visibility
320 GC, 320 and 323 Excavator Machine Systems Bucket System
320 GC, 320 and 323 Excavator Machine Systems Stick System
320 GC, 320 and 323 Excavator Machine Systems Boom System
120 and 120 AWD Motor Grader Battery Disconnect Switch
120 and 120 AWD Motor Grader Parking
120 and 120 AWD Motor Grader Engine Shutdown Switch - Check
120 and 120 AWD Motor Grader Seat
A New NRS Coolant Return Line Clamp is Now Used on Certain C15 and C18 Engines {1355, 1380, 1393} A New NRS Coolant Return Line Clamp is Now Used on Certain C15 and C18 Engines {1355, 1380, 1393}
Update required for 498-6540 and 498-6541 Tensioner Pump Groups used for 3600 Rod Bolt Tensioning {0374, 0599, 1000, 1218, 1219, 7610, 7620} Update required for 498-6540 and 498-6541 Tensioner Pump Groups used for 3600 Rod Bolt Tensioning {0374, 0599, 1000, 1218, 1219, 7610, 7620}
C9.3B Engine Engine Throttle Valve - Test
3500B Generator Sets Generator Bearing - Replace
3516B Generator Set Engines with Dynamic Gas Blending Calibration - <B>175-4998</B> Signal Converter
C9.3B Engine Electrical Power Supply - Test
G3304 and G3306 Engines Engine Balancer Shaft - Remove and Install
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Gear Cover - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Travel Motor - Remove and Install
PM620 and PM622 Cold Planer Water Spray Pump Oil Level (High Pressure) - Check
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Tank Not Filling