Engine Balancer Shaft - Remove and Install
Start By:
- Remove the timing gear cover.
- Remove the oil pump.
- Position the engine to top center compression stroke. Refer to Testing and Adjusting , Finding Top Center Position for No. 1 Piston for correct procedure.
Show/hide table
Illustration 1 g06190124 - Remove bolts (1) and the washers. Remove lock plate (2).
Show/hide table
Illustration 2 g06190127 - Remove engine balancer shaft (3). Repeat Steps 2 and 3 for other side.
- Apply clean engine oil on the balancer shaft.
Show/hide table
Illustration 3 g06190124 Show/hide tableIllustration 4 g06190127 - Install engine balancer shaft (3). Install lock plate (2), the washers, and bolts (1). Repeat for other side.
- Turn both balancer shafts (3) until the flat part on each shaft is away from the oil pan plate. Install two 3/8"-16 NC bolts 1 1/2" long through the oil pan plate and into the holes in the balancer shafts. The bolts will make the shafts so the balancer shafts will not turn. Do not tighten the bolts against the bottom of the holes in the shafts.
- Install the oil pump. Refer to Disassembly and Assembly , Oil pump - Remove and Install for correct procedure.
- Remove the two 3/8"-16 NC bolts from the balancer shafts. Ensure that the balancer shaft timing is correct. The balancer shaft timing is correct when the holes in the balancer shafts are in alignment with the holes in the oil pan plate, and No. 1 piston is at the top center compression position.
End By:
- Install the timing gear cover.
Caterpillar Information System:
C9.3B Engine Electrical Power Supply - Test
3516B Generator Set Engines with Dynamic Gas Blending Calibration - <B>175-4998</B> Signal Converter
3500B Generator Sets Generator Bearing - Replace
C9.3B Engine Engine Throttle Valve - Test
Update required for 498-6540 and 498-6541 Tensioner Pump Groups used for 3600 Rod Bolt Tensioning {0374, 0599, 1000, 1218, 1219, 7610, 7620} Update required for 498-6540 and 498-6541 Tensioner Pump Groups used for 3600 Rod Bolt Tensioning {0374, 0599, 1000, 1218, 1219, 7610, 7620}
A New NRS Coolant Return Line Clamp is Now Used on Certain C15 and C18 Engines {1355, 1380, 1393} A New NRS Coolant Return Line Clamp is Now Used on Certain C15 and C18 Engines {1355, 1380, 1393}
120 and 120 AWD Motor Grader Seat
320GC, 320 and 323 Excavators Machine Systems Track Carrier Roller - Remove and Install
PM620 and PM622 Cold Planer Water Spray Pump Oil (High Pressure) - Change
320GC, 320 and 323 Excavators Machine Systems Track Roller - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Front Idler and Recoil Spring - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Counterbalance Valve (Travel) - Remove and Install
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Gear Cover - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Travel Motor - Remove and Install
PM620 and PM622 Cold Planer Water Spray Pump Oil Level (High Pressure) - Check
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Tank Not Filling
C175 Tier 4 Final Engines for Off-Highway Trucks Electronic Service Tools
C175 Tier 4 Final Engines for Off-Highway Trucks Engine Monitoring System
C9.3 Tier 4 Final Engines Turbocharger Balance Valve Air Lines
C175 Tier 4 Final Engines for Off-Highway Trucks Coolant Temperature Is High
An Improved Monitor Display Group Is Now Used on Certain C32 Marine Engines {7490} An Improved Monitor Display Group Is Now Used on Certain C32 Marine Engines {7490}
C175 Tier 4 Final Engines for Off-Highway Trucks Coolant Temperature Is Low
New Exhaust Heat Shields Are Now Used on Certain 3500C Series Engines {1063, 1067} New Exhaust Heat Shields Are Now Used on Certain 3500C Series Engines {1063, 1067}
3500B Generator Sets Generator Bearing - Inspect