Water Spray Pump Oil (High Pressure) - Change
Show/hide table
 |
|
熱機油和高溫組件會導致人員受傷。 請勿讓熱油接觸到皮膚。 |
Show/hide table
| 注意事項 |
|---|
|
在檢驗、保養、測試、調整及修理產品時，請小心確保油液有容器盛裝。 在打開任何艙室或拆卸任何含有用液的組件前，應準備好盛裝用液的適當容器。 請參閱特別出版品, P4RJ1017, "代理商維修工具目錄"，以瞭解適合用來收集及容納 Cat® 產品之液體的工具和耗材。 按照當地的條例和法規棄置廢棄的油液。 |
- 取下排放塞 (1)，將機油排放到合適的容器內。
附註泵的容量為
0.4 L (0.1 US gal) 。 - 清潔排放塞 (1)。 裝回排放塞 (1)。
- 取下注油塞 (2)。
- 透過注油塞開口添加機油，直到油位處於目視儀表中的一半。 請參閱操作及保養手冊, "加注容量"。
- 清潔注油塞 (2)。 裝回注油塞 (2)。
Show/hide table
| |
| 插圖 1 | g00851504 |
|
典型範例 | |
Caterpillar Information System:
320GC, 320 and 323 Excavators Machine Systems Track Roller - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Front Idler and Recoil Spring - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Counterbalance Valve (Travel) - Remove and Install
320 GC, 320 and 323 Excavator Machine Systems Machine System
120 and 120 AWD Motor Grader Restricted Visibility
320 GC, 320 and 323 Excavator Machine Systems Bucket System
320 GC, 320 and 323 Excavator Machine Systems Stick System
320 GC, 320 and 323 Excavator Machine Systems Boom System
120 and 120 AWD Motor Grader Battery Disconnect Switch
120 and 120 AWD Motor Grader Parking
120 and 120 AWD Motor Grader Engine Shutdown Switch - Check
120 and 120 AWD Motor Grader Battery or Battery Cable - Inspect/Replace
320GC, 320 and 323 Excavators Machine Systems Track Carrier Roller - Remove and Install
120 and 120 AWD Motor Grader Seat
A New NRS Coolant Return Line Clamp is Now Used on Certain C15 and C18 Engines {1355, 1380, 1393} A New NRS Coolant Return Line Clamp is Now Used on Certain C15 and C18 Engines {1355, 1380, 1393}
Update required for 498-6540 and 498-6541 Tensioner Pump Groups used for 3600 Rod Bolt Tensioning {0374, 0599, 1000, 1218, 1219, 7610, 7620} Update required for 498-6540 and 498-6541 Tensioner Pump Groups used for 3600 Rod Bolt Tensioning {0374, 0599, 1000, 1218, 1219, 7610, 7620}
C9.3B Engine Engine Throttle Valve - Test
3500B Generator Sets Generator Bearing - Replace
3516B Generator Set Engines with Dynamic Gas Blending Calibration - <B>175-4998</B> Signal Converter
C9.3B Engine Electrical Power Supply - Test
G3304 and G3306 Engines Engine Balancer Shaft - Remove and Install
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Gear Cover - Remove and Install
320GC, 320 and 323 Excavators Machine Systems Travel Motor - Remove and Install
PM620 and PM622 Cold Planer Water Spray Pump Oil Level (High Pressure) - Check