Transmission Planetary
Show/hide table
Illustration 1 | g03759710 |
Show/hide table
Speed Selection Clutch Engagement | |||||||
---|---|---|---|---|---|---|---|
Clutch 1 | Clutch 2 | Clutch 3 | Clutch 4 | Clutch 5 | Clutch 6 | LUC | |
Park | X | X | X | ||||
Neutral 1 | X | X | |||||
Neutral 2 | X | X | |||||
1 Forward | X | X | X | ||||
2 Forward | X | X | X | X | |||
3 Forward | X | X | X | X | |||
4 Forward | X | X | X | X | |||
5 Forward | X | X | X | X | |||
6 Forward | X | X | X | X | |||
7 Forward | X | X | X | X | |||
8 Forward | X | X | X | X | |||
9 Forward | X | X | X | X | |||
1RC | X | X | X | ||||
2RC | X | X | X |
Show/hide table
Illustration 2 | g03798274 |
(1) Clutch 1
(2) Clutch 2 (3) Clutch 3 (4) Clutch 4 (5) Clutch 5 (6) Clutch 6 (7) Output shaft |
The planetary transmission has nine forward speeds and two reverse speeds. "REVERSE" and "NEUTRAL" use only torque converter drive. At lower speeds, "FIRST" gear "FORWARD" uses torque converter drive mode.
The two Transmission Output Speed Sensors (not shown) determine the speed and direction of the Output Shaft (7). The signal from these sensors is considered by the Transmission ECM for shifting strategies.
Caterpillar Information System:
A New Rock Arm Shaft Bracket Is Now Used for Certain G3306 Engines {1102} A New Rock Arm Shaft Bracket Is Now Used for Certain G3306 Engines {1102}
G3516 Petroleum Engine Turbocharger - Inspect
Identifying Oil Pumps on Certain 3400, C27, and C32 Engines {1304} Identifying Oil Pumps on Certain 3400, C27, and C32 Engines {1304}
G3516 Petroleum Engine Overhaul (Top End)
CX38-P892 Well Servicing Transmission Oil Filter (Transmission)
C175 Tier 4 Final Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C175 Tier 4 Final Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3516 Petroleum Engine Overhaul (Major)
G3516 Petroleum Engine Ignition System Timing - Check/Adjust
G3516 Petroleum Engine Inlet Air System - Check
CX38-P892 Well Servicing Transmission Power Train Hydraulic System
C9.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Procedure to Measure Valve Recession for C175 Engines {0759, 0760, 1100, 1105} Procedure to Measure Valve Recession for C175 Engines {0759, 0760, 1100, 1105}
C12.9 Marine Propulsion Engine Fuel System - Inspect
C7.1 Marine Propulsion Engine Fuel Conservation Practices
C12.9 Marine Propulsion Engine Finding Top Center Position for No. 1 Piston
C9.3B Engines for Caterpillar Built Machines Flywheel - Remove
C12.9 Marine Propulsion Engine Fuel System Pressure - Test
G3516 Petroleum Engine Fuel Metering Valve - Check
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Electric Retarder - Disassemble - Grid Assembly
G3516 Petroleum Engine Coolant (NGEC) - Change
C12.9 Marine Propulsion Engine Rear Gear Group - Time
XQP1100 Generator Set Maintenance Interval Schedule - Prime
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Diagnostic Trouble Codes