Engine Oil Level - Check
Show/hide table
注意事項 |
---|
Caterpillar 建議定期採集油樣並進行 SOS 機油分析,以防損壞組件。 使用本 OMM (Operation and Maintenance Manual, 操作及保養手冊) 當中「取樣週期及取樣閥的位置」中的資訊,找到適合您機器的適當採樣週期。 |
Show/hide table
注意事項 |
---|
請勿過度加注曲軸箱。 否則引擎可能損壞。 |
- 檢查液位前請讓機器保持水平,以確保取得正確的液位。
- 升起引擎蓋。
偏好設定: 請參閱操作及保養手冊, "機蓋傾斜",以瞭解升起此機器機蓋的正確程序。
Show/hide table插圖 1 g03706714 Show/hide table插圖 2 g00999790 - 引擎停止時,讓油位保持在引擎機油油位尺 (2) 的交叉陰影線區域 (A)。
- 取下機油加注口蓋 (1)。 如有必要,請添加機油。
- 清理機油加注口蓋,然後裝上機油加注口蓋。
- 蓋上引擎蓋。
Caterpillar Information System:
C15 and C18 Tier 4 Final Engines Diesel Exhaust Fluid Quality - Test
C8.7 Marine Engine Decommissioning and Disposal
PM620 and PM622 Cold Planer Coolant Sample (Level 1) - Obtain
PM620 and PM622 Cold Planer Cooling System Coolant Level - Check
PM620 and PM622 Cold Planer Cooling System Coolant (ELC) - Change
C8.7 Marine Engine Fumes Disposal Filter Element - Replace
PM620 and PM622 Cold Planer Conveyors - Lubricate
C8.7 Marine Engine Fuel System Secondary Filter - Replace
PM820, PM822, and PM825 Cold Planer Belt - Inspect/Adjust/Replace
C0.5 and C0.7 Industrial Engines Mounting and Dismounting
C8.7 Marine Engine Engine Oil and Filter - Change
PM620 and PM622 Cold Planer Battery or Battery Cable - Inspect/Replace
460-8974 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-8974 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
C9.3 Industrial Engine and CX31-P600-C9I Petroleum Power Train Package Maintenance Interval Schedule
PM820, PM822, and PM825 Cold Planer Fuel Tank Water and Sediment - Drain
PM820, PM822, and PM825 Cold Planer Hydraulic Foldable Canopy Cylinder Ends - Lubricate
PM620 and PM622 Cold Planer Hydraulic System Oil Level - Check
PM620 and PM622 Cold Planer Hydraulic System Oil Sample - Obtain
460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
PM820, PM822, and PM825 Cold Planer Legs (Struts) - Lubricate
PM820, PM822, and PM825 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
XQC1200 and XQC1600 Power Modules Inlet Manifold Pressure Sensor - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet Manifold Temperature Sensor - Remove and Install
C8.7 Marine Engine Crankshaft Vibration Damper - Inspect