ECM Mounting Bracket - Remove and Install
开始:
- 拆下电子控制模块(ECM)。 有关正确步骤,请参阅拆解和组装, "电子控制模块 - 拆卸和安装"。
- 将电缆带 (1)、电缆带 (4) 和电缆带 (9) 从导线线束组件 (8) 上切断。
注: 标注将导线线束组件连接到 ECM 安装支架的电缆带位置。
- 将导线线束组件 (8) 远离 ECM 支架 (10)。
- 将螺栓 (5) 从塑料管组件 (7) 的支架 (6) 上拆下。
- 将塑料管组件和支架远离 ECM 支架 (10)。
- 将螺母 (2) 从母线绝缘体上拆下,将线束 (3) 从母线绝缘体上断开。
Show/hide table
图 2 g03397465 - 将螺栓 (11) 从 ECM 支架 (10) 上拆下。 拆卸螺栓过程中,支承支架。
- 将 ECM 支架 (10) 从缸体 (12) 上拆下。
Show/hide table
图 1 | g03397464 |
- 确保 ECM 支架清洁、无损坏。 如果 ECM 支架损坏,则进行更换。
Show/hide table
图 3 g03397465 - 将 ECM 支架 (10) 定位在缸体上。 确保支架朝向正确。
- 将螺栓 (11) 安装到 ECM 支架 (10) 上。 安装螺栓过程中,支承支架。
- 拧紧螺栓 (11) 至扭矩为
22 N·m (195 lb in) 。Show/hide table图 4 g03397464 - 将导线线束组件 (8) 定位到 ECM 支架 (10) 上。
- 将新的电缆带 (1)、电缆带 (4) 和电缆带 (9) 安装到导线线束组件 (8) 上。
注: 确保电缆带符合原始设备制造商(OEM)的技术规格。
- 将塑料管组件 (7) 和支架 (6) 定位到 ECM 支架 (10) 上。
- 将螺栓 (5) 安装到塑料管组件 (7) 的支架 (6) 上。
- 拧紧螺栓 (5) 至扭矩为
22 N·m (195 lb in) 。 - 将线束 (3) 连接到母线绝缘体。
- 安装螺母 (2)。 拧紧螺母至扭矩为
10 N·m (88 lb in) 。
结束:
- 安装电子控制模块。 有关正确步骤,请参阅拆解和组装, "电子控制模块 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Engines Cylinder Head - Remove
C7.1 Engines Cylinder Head - Install
C7.1 Engines Crankshaft Timing Ring - Remove and Install
C7.1 Engines Crankshaft Rear Seal - Remove
C7.1 Engines Crankshaft Rear Seal - Install
C7.1 Engines Crankshaft Position Sensor - Remove and Install
C7.1 Engines Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 Engines Crankshaft Gear - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft - Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines Electronic Control Module - Remove and Install
349F and 352F Excavators Machine System Specifications Track
C280-16 Engine Fluid Recommendations
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
C7.1 Engines Electronic Unit Injector - Install
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base