Crankshaft Rear Seal - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 227-4390 | E12 Torx 套筒 | 1 |
B | FT-2806 | 定位工具 | 1 |
注: 曲轴后油封和壳体是以一个组件制造的。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保曲轴法兰 (1) 清洁、干燥、无损坏。 用不起毛的布清洁曲轴法兰。
- 确保缸体表面和桥接件清洁、干燥。
- 提供的新曲轴后油封带有一个塑料套管 (3)。 确保安装时塑料套管的四个角在曲轴后油封 (2) 以内。
注: 提供塑料套管是为了在把油封推过曲轴法兰时保护油封唇。
注: 请勿润滑曲轴后密封或曲轴法兰。 曲轴后油封在安装时必须干躁。
- 对齐塑料套管 (3) 与曲轴法兰 (1)。 确保塑料套管在曲轴法兰上啮合。 将新曲轴后油封 (2) 的四角推到曲轴法兰上。
在这个操作过程中,会把塑料套管压出曲轴后油封。 弃置塑料套管。
- 将曲轴后油封 (2) 上的两个模压定位件与缸体中的孔对齐。 确保曲轴后密封抵在缸体上就座。
曲轴后油封拧紧顺序
Show/hide table图 3 g03364098 - 安装 torx 螺钉 (4),用手拧紧。
注: 此时不要将 torx 螺钉安装到部位 (X) 处。
- 将工具 (B) 安装到曲轴后油封 (2) 及曲轴法兰 (1) 上。
- 使用工具 (A) 拧紧 torx 螺钉 (4) 至扭矩为
22 N·m (195 lb in) 。 按照图 3 中所示的顺序拧紧 torx 螺钉 (4)。 - 拆下工具 (B)。
- 将其余的 torx 螺钉 (4) 安装到位置 (X) 处。 使用工具 (A) 拧紧 torx 螺钉至扭矩为
22 N·m (195 lb in) 。 参考图 3。
Show/hide table
图 1 | g03413500 |
Show/hide table
图 2 | g03364097 |
结束:
- 安装飞轮。 请参阅拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
C7.1 Engines Crankshaft Position Sensor - Remove and Install
C7.1 Engines Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 Engines Crankshaft Gear - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft - Install
C7.1 Engines Crankcase Breather - Remove - Unfiltered Breather
C7.1 Engines Crankcase Breather - Install - Unfiltered Breather
C7.1 Engines Crankcase Breather - Remove - Filtered Breather
C7.1 Engines Crankcase Breather - Install - Filtered Breather
C7.1 Engines Coolant Temperature Sensor - Remove and Install
C7.1 Engines Crankshaft Rear Seal - Remove
C7.1 Engines Crankshaft Timing Ring - Remove and Install
C7.1 Engines Cylinder Head - Install
C7.1 Engines Cylinder Head - Remove
C7.1 Engines ECM Mounting Bracket - Remove and Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines Electronic Control Module - Remove and Install
349F and 352F Excavators Machine System Specifications Track
C280-16 Engine Fluid Recommendations
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
C7.1 Engines Electronic Unit Injector - Install