Crankshaft Front Seal - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 278-2636 | 前油封拆卸工具 | 1 |
开始:
- 拆下曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 安置在曲轴的鼻端。 将工具 (A) 拧入曲轴前油封 (1)。
注: 请勿损坏曲轴前油封的壳体边缘。
- 将螺栓 (2) 拧入工具 (A) 以拆卸曲轴前油封 (1)。
Show/hide table
图 1 | g03429500 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 9U-6206 | 螺柱前油封安装工具 | 1 |
9U-6207 | 板 | 1 | |
9U-6209 | 套筒板 | 1 | |
9U-6211 | 油封安装工具 | 1 | |
366-5984 | 安装工具组件 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保前壳体中的曲轴前油封孔清洁、无损坏。
Show/hide table
图 2 g03429501 - 组装工具 (B)。
- 将新的曲轴前密封 (1) 与前壳体对准。
注: 如果随曲轴前油封提供了套筒,安装之前,将套筒从曲轴前油封上拆下。
- 使用工具 (B) 安装曲轴前油封 (1)。 确保密封正面在前齿轮室中的安装深度为
6.5 ± 0.2 mm (0.256 ± 0.008 in) 。 - 将工具 (B) 从曲轴上卸下。
结束:
- 安装曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft - Install
C7.1 Engines Crankcase Breather - Remove - Unfiltered Breather
C7.1 Engines Crankcase Breather - Install - Unfiltered Breather
C7.1 Engines Crankcase Breather - Remove - Filtered Breather
C7.1 Engines Crankcase Breather - Install - Filtered Breather
C7.1 Engines Coolant Temperature Sensor - Remove and Install
C7.1 Engines Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Engines Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Engines Camshaft Gear - Remove and Install
C7.1 Engines Camshaft Bearings - Remove and Install
C7.1 Engines Crankshaft Gear - Remove and Install
C7.1 Engines Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 Engines Crankshaft Position Sensor - Remove and Install
C7.1 Engines Crankshaft Rear Seal - Install
C7.1 Engines Crankshaft Rear Seal - Remove
C7.1 Engines Crankshaft Timing Ring - Remove and Install
C7.1 Engines Cylinder Head - Install
C7.1 Engines Cylinder Head - Remove
C7.1 Engines ECM Mounting Bracket - Remove and Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines Electronic Control Module - Remove and Install
349F and 352F Excavators Machine System Specifications Track