Camshaft Bearings - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
B | 8H-0684 | 棘轮扳手 | 1 |
开始:
- 拆下发动机机油泵。 有关正确的步骤,请参阅拆解和组装, "发动机机油泵 - 拆卸"。
- 拆下凸轮轴。 有关正确步骤,请参阅拆解和组装, "交流凸轮轴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查凸轮轴轴承 (1)。 有关更多资料,请参阅技术参数, "凸轮轴轴承"。
- 如果凸轮轴轴承 (1) 磨损或损坏,使用工具 (A) 将凸轮轴轴承从缸体上拆下。
注: 将凸轮轴轴承从缸体前部拆下。
Show/hide table
图 1 | g02010213 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
B | 8H-0684 | 棘轮扳手 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁缸体中的轴承壳体。 确保轴承壳体的油孔中没有碎屑。
Show/hide table
图 2 g02010216 - 使用清洁的发动机机油润滑缸体中的轴承壳体。
- 准确地对准凸轮轴轴承 (1) 上的大油孔 (X) 与缸体上的油孔。
注: 凸轮轴轴承中的凹槽 (Y) 必须处于缸体顶部。
- 使用工具 (A),将凸轮轴轴承 (1) 安装到缸体中。 安装凸轮轴轴承,使轴承前沿与缸体中的凹槽面平齐。
注: 确保已将所有油孔正确对准。 如果没有正确对准油孔,应拆卸凸轮轴轴承。
结束:
- 安装凸轮轴。 有关正确步骤,请参阅拆解和组装, "交流凸轮轴 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Engines Camshaft - Remove and Install
C7.1 Engines Boost Pressure Sensor - Remove and Install
C7.1 Engines Alternator Belt - Remove and Install
C7.1 Engines Alternator - Remove
C7.1 Engines Alternator - Install
C7.1 Engines Air Compressor - Remove and Install - Twin Cylinder Air Compressor
C7.1 Engines Air Compressor - Remove and Install - Single Cylinder Air Compressor
C7.1 Engines Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C7.1 Engines Accessory Drive - Remove and Install - Accessory Drive SAE "A"
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Power Sources
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Additional UPS Concepts
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Front Panel Overview
C7.1 Engines Camshaft Gear - Remove and Install
C7.1 Engines Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Engines Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Engines Coolant Temperature Sensor - Remove and Install
C7.1 Engines Crankcase Breather - Install - Filtered Breather
C7.1 Engines Crankcase Breather - Remove - Filtered Breather
C7.1 Engines Crankcase Breather - Install - Unfiltered Breather
C7.1 Engines Crankcase Breather - Remove - Unfiltered Breather
C7.1 Engines Crankshaft - Install
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft Front Seal - Remove and Install