Crankshaft Gear - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 8H-0663 | 轴承拉拔器 | 1 |
5F-7345 | 螺钉 | 1 | |
126-7183 | 十字挡块 | 1 | |
126-7177 | 拉拔器腿 | 2 |
开始:
- 拆卸前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 拆卸"。
- 拆下发动机机油泵。 有关正确的步骤,请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
图 1 | g03432370 |
- 使用工具 (A) 将曲轴齿轮 (4) 从曲轴 (2) 上拆下。
- 必要时,将键 (1) 和摩擦片 (3)(如有配备)从曲轴 (2) 上拆下。
注: 除非键损坏,否则不要从曲轴上卸下键。
Show/hide table
图 2 | g03432371 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | - | 热板 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
Show/hide table
图 3 g03432372 - 如有必要,将新的摩擦片 (3)(如有配备)安装到曲轴 (2) 上。
- 如有必要,将新的键 (1) 安装到曲轴 (2) 上。
Show/hide table
灼热的零件或部件会烫伤人体。 别让灼热的零件或部件触及您的皮肤。 为了保护您的皮肤,必须穿上保护衣或使用保护装备。
- 使用工具 (B) 将曲轴齿轮 (4) 加热至温度为
150° ± 50°C (302° ± 90°F) 。 对准曲轴齿轮 (4) 中的键槽与曲轴中的键 (1)。 将曲轴齿轮 (4) 安装到曲轴 (2) 上。 确保曲轴齿轮 (4) 的肩 (5) 朝向发动机前部。注: 不要使用喷枪加热曲轴齿轮。
结束:
- 安装前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 安装"。
- 安装发动机机油泵。 有关的正确步骤,请参阅拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C7.1 Engines Crankshaft Front Seal - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft - Install
C7.1 Engines Crankcase Breather - Remove - Unfiltered Breather
C7.1 Engines Crankcase Breather - Install - Unfiltered Breather
C7.1 Engines Crankcase Breather - Remove - Filtered Breather
C7.1 Engines Crankcase Breather - Install - Filtered Breather
C7.1 Engines Coolant Temperature Sensor - Remove and Install
C7.1 Engines Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Engines Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Engines Camshaft Gear - Remove and Install
C7.1 Engines Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 Engines Crankshaft Position Sensor - Remove and Install
C7.1 Engines Crankshaft Rear Seal - Install
C7.1 Engines Crankshaft Rear Seal - Remove
C7.1 Engines Crankshaft Timing Ring - Remove and Install
C7.1 Engines Cylinder Head - Install
C7.1 Engines Cylinder Head - Remove
C7.1 Engines ECM Mounting Bracket - Remove and Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines Electronic Control Module - Remove and Install
349F and 352F Excavators Machine System Specifications Track
C280-16 Engine Fluid Recommendations